-
Posts
13 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Posts posted by Twirl My Fuzz
-
-
1 hour ago, mackman said:
Short answer I do and it does
thanks.
-
does anyone use freebase nicotine in their lost vape orion? does it vape as well as salt nicotine?
thanks.
-
42 minutes ago, Dragandeewhy said:
Ok ..but what will happen if I set 30watts.
will the pods be able to take it?
I set it to 30 watts one time with boost set to 11 with the .25 ohm coil
The pod tasted burnt though
You can try it for yourself
-
42 minutes ago, retird said:
Hopefully you have more than 1 pod..... hope you find your happy place....
it didn't permanently burn pod.
-
On 10/17/2018 at 5:36 AM, retird said:
Setting it to maximum everything may overdrive the coils in the pods..... may put a bad taste in your mouth.... 😊 I'm running the DL pod (0.25) at 15 watts and the MTL pod (0.50) at 12 watts...
you were right, it tasted burnt when i maxed everything out. i ended up resetting it to default settings with maximum boost and maximum warmth. hits fine.
thanks.
-
On 10/18/2018 at 5:58 PM, Wayneo said:
In your other post, you were already told 30 watts, boosting to 40. The answer will not change.
Boost and warmth - 11.
Tiny 900mAh battery (large for pods)
Many are vaping in the 11 - 13 watt range on these non rebuildable pods.
This is not an Aromamizer Titan atty holding 30ml of juice sitting on a 400 watt 4S Lipo.
Thanks.
-
Yo vapers.
Can somebody list all of the maximum settings that I can put everything to? Wattage, boost, warmth, etc.
Thanks.
-
On 9/17/2018 at 5:00 AM, Vape_Like_A_Boss said:
Did you disable the MTL by unchecking the checkbox for "enable" in escribe to force the MTL profile with the .25 coil? I'm wondering if that's what's throwing off the resistance due to a bug or it just happens to be that coil or the way it's making contact at the pin. I'm curious as I've been wondering about disabling the MTL setting so there's only one profile, although I don't really have any need for it, just trying to figure out how the system works. And I figured I throw it out there to help define the exact settings for where the issue is. But that's only the case if the post about not trying MTL above was still the case when you made this later post.
"Did you disable the MTL by unchecking the checkbox for "enable" in escribe to force the MTL profile with the .25 coil? "
i am trying to understand, by unchecking mouth to lung wouldn't that force the device to perform direct lung?
-
15 hours ago, DrewBurton50 said:
I think that I am correct in saying that the maximum wattage that you can set is 30w and
40w is the maximum that can be achieved by the boost setting.
that means one would receive 40w at the beginning of the puff but it will taper off to 30w? btw what is the highest level you can set boost to?
-
14 hours ago, retird said:
Setting it to maximum everything may overdrive the coils in the pods..... may put a bad taste in your mouth.... 😊 I'm running the DL pod (0.25) at 15 watts and the MTL pod (0.50) at 12 watts...
do you get decent clouds with the .25 at 15 watts? btw it seems you happened to get a functioning device, many people on this forum received duds.
- 1
-
hi markse68
did you take apart the device?
-
sup guys.
has anybody set the wattage to forty? i just ordered it n i want to set it to maximum everything. what do you guys think? n also, if not forty, what wattage + settings are all of you running it on?
thanks.
DNA Go Lost Vape Orion (Original)
in General Discussion
Posted
Hello!!!
To anyone who has disassembled and successfully reassembled the original Lost Vape Orion:
After taking this mod apart, there seems to be some silver contact on one of the faceplates and when the faceplates aren't sealed tightly against the battery, the mod tends to disconnect randomly until firm pressure is applied on the faceplates. Any tips on securing these faceplates onto the mod tightly? Silicon glue perhaps? Or, should the faceplates not be a factor on the Lost Vape Orion functionality, and is my mod in fact starting to "fail" at some deeper level, perhaps at one of the wire connections?
Any technical tips are greatly appreciated.
Much thanks!