-
Posts
13 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Posts posted by Beissen
-
-
Anyone have a good Power Curve chart that will allow a single 18650 last longer sems mine dies fast and Im at 1.161 ohms at 16.5w on Ni80. I want to have better life.
-
On 8/29/2018 at 2:38 AM, skuck said:
I'm opening escribe 2.0 and connecting the USB cable but it never registers that there's a device attached. I open the Device manager and it shows no USB devices attached while the mod is connected. The cable works because I can connect other devices but just not with my DNA 75c mod. Is the a driver that I need to download or is it a USB 3,.0m problem? Is the DNA 75c not compatible with USB 3.0? I can't imagine that Evolv would release a board that isn't compatible with the new USB standards. Anyone have any information on this?
go get a USB Hub 2,0 from best buy a cheap one it will drop the 3.0 to a 2.0 and it will fix it.
-
Motherboard dont matter its the USB ports. Now all ports worked with the update and I'm also on international as well and a PC. Try removing all of escribe then re download the international version (Its better anyway) and see if it fixes the problem.
-
1 hour ago, arby said:
I'm necroing this thread, I know its old but I am having issues with my 75C connecting. I've tried everything in this thread. Using the OG escribe software for when the 75C or 250C chip came out all the way to the newest SP. No luck, I am about to make a W7 virtual drive and try it in there if I have to. But I wanted to know if there has been any development that hasn't been posted or discovered that has solved this before I go digging for my Tiny7 install.
Its worked now but what i did was buy a USB Hub taking the 3.1 usb back to a 2.0 cheap and easy plugged that in and then plugged the cable to the mod and no issues. Hope that helps.
-
They do not all are knowledgeable onnit just have to read the package and its says USB 2.0 It was like 14.99 at best buy where all the hubs are at my best buy it was facing geek squad.
-
7 hours ago, skuck said:
Where do you get an adapter from?
You can go to best buy or any electronics store.
-
OK, I had a issue with the New Laptop this for those with a issue later or now that have not figured it out. Its a simple Fix go get a USB 2.0 Adapter it will convert the 3.1 to a 2.0 and then it allows you to read the Mod itself and do everything again.
-
Having the same issue, connected day one of new purchase of my Dell, then the next day after the Bios updated wont reconize the mod being plugged in. I tried my other laptop and it works fine.
-
I got a new Laptop (Dell G7) and Escribe worked the first day and then today went to plug in and its not recognizing my device being plugged in to the PC via USB, I pulled my other laptop out and it works just fine on it. Same cable and all so its not a cable issue. What can I do as this is for a DNA75C?
Already-
Restarted the PC
Uninstalled and reinstalled the Escribe Software
-
I am new to the new Color layout and before this was so easy to do. But how do I get the Battery to displace the % vs a Battery itself?
-
On 4/19/2018 at 5:08 PM, Val said:
good afternoon!!! how come my mod does not display the New Coil message whenever i swith atomizers? Is this normal?
I am having the same issue on my Therion DNA166.
75c Battery Calibration
in General Discussion
Posted
So after reading I see what you mean dwcraig1 and also Wayneo I have a 30q, my setting were off as I now know adjust based on Amp to adjust those settings and it read right as the 30Q is only 15 Amps and I had it set to 30 Max and Discharge at 25 now its reading right.