latexyankee

What about the 3 factory ni200 coils I've tried? All bad?

Downloaded the settings from Wismec and uploaded the .ecig file to device before I even had my first vape. I've used the atty analyzer but i'm unsure of what it does. I thought it was more of a test, says that resistance should change on tightening. The atty does jump around so i figured it was ok, i dont remeber seeing an option to save or whatever but i was drinking and very tired. Ill check that again later. Any other ideas before i ship it off? Again, it worked ONCE on my second build for a few hours at night and in the morning using 28g dual ni200. I switched on the tank to drive to work and after that all went to hell tc has never returned. My builds are pretty solid, i can usually spot a defect on my part, post holes are tight on the velocity, stripped one of the screws second guessing myself. Been about 12 hours of frustration over the past 2 days, i am out of ideas.

Can you give an example of a build that won't work in TC mode? What wire, starting resistance and atomizer? Typically TC mode failure is usually the 510 connection or atomizer. Though it has been stated many times on this forum, if your 510, its associated wiring or your atomizer has a substantial initial resistance, and your build is very low resistance, then the change in resistance the mod sees will be small as a percentage and therefore it will assume the wire is non-TC wire. [/QUOTE] Any build that is not Kanthal. Lets see... Single 28g ni200 Single 26g ni200 Dual 28g ni200 Dual 26g ni200 Ni200 clapton 26/28 Ni200 clapton 28/30 Cci triforce prebuilt coil head at .1 ohms, tried 2 of them. For attys using a velocity clone and a Alliance.

Yes temp control is off is NOT checked. Wire is ni200, I've also tried 2 titanium builds Atty is velocity clone, and ive used several prebuilt ni200 coil heads...no dice.

In escribe there is no 'ON" for temp control it's simply checked by a radio button which is dark confirming my temp level. My other options are off or locked and I've left it default which I assume is on. My ohm lock range is 25%, I got his all from the wismec site when they released their settings for the software. I assume ohm lock range is when it asks "new atty same atty" I'll admit lately tonight it has been asking me more but no matter what it will not recognize TC, whether it's my 2 atty builds or 2 different tanks with ni200 coils. All 4 fail immediately. I only have 2 profiles, one for Ti and for ni200 ( which i shouldn't have cause the device is supposed to recognize nickel and autoswitch but I made the profile in an attempt to rectify the issue) the TCR for titanium was downloaded through steam engine wire wizard but..we never even got that far cause regardless of profile device fires in power mode. I have an ni200 profile which i switch to every 10 minutes but fires in power mode. My ni200 tank coils will not register as TC either fire in power mode regardless of profile. Mod resistance is .003 this was from wismec site which they released the other day. Latest and greatest. this was the one thing I was looking into but couldn't find much. Seems sketchy but came from manufacturer files. YES meant .09 Have spent about 12 hours troubleshooting Thanks for the reply

Mods please move this to the report bugs, I posted in the wrong section

Same issue, tried 10 or so builds, brand new device. TC has not worked yet with ni200 or TI everything fires as kanthal regardless of profile set. Caught fire in my mouth at work, these seem to be pretty shabby boards.

Like the title says I am never asked for new coil, UNLESS I use the same coil. For instance if I unscrew my kanthal tank to refill, reattach in 30 seconds I am prompted with the new coil message. If I switch to ni200 or Ti, I never get the message and the device usually fires in power mode. I have a profile set for ni200 and titanium and I'll switch to that profile first, attach atty and it will fire in power mode. I've had the device ask me new atty a number of times, I'd say 10% and even though it's a TC build the device refuses to run in temp mode. This is my first dna 200 chip, but I'm very experienced (6+years) so I feel I am missing something. I trust the chip and the device(wismec reulaux) but what is the common denominator here? I've watched loads of videos and followed certain procedures to a T. As far as my build I recognize it could always be a problem but the device should adhere to my profiles correct? I would say 75% of my atty builds are spot on. EDIT- Just attached a brand new ni200 dual wrapped at .009...I was asked if new coil selected, yes and I was already set to my ni200 profile. Temp control is NOT active device monitor shows zero temp activity and the mod itself cuts off temp when fired. This has has happened for 6 straight days now on every type of TC build. All gauges of ni200, TI, claptons etc....I'm desperate here. I do not get a spike in device monitor for the temp reading, it simply will not function

Do I have to download a new .csv for every build? For instance I selected my gauge and type of wire and exported the csv file for the dna 200, but does the build section on the left side matter? I've always used that to get an appropriate estimate on my potentail wraps and such but I wasnt sure if that played into the downloaded file. Does that make sense?