norwegianvaper
-
Posts
14 -
Joined
-
Last visited
Never
Content Type
Profiles
Forums
Downloads
Posts posted by norwegianvaper
-
-
ChunkyButt200 said:
i remember the fundraiser for that mod that Peg was doing. i also remember a chinese company almost ran off with the money, lol. at least it he made it happen. depending on the available space inside the mod and how it's set up, you most likely could convert it to a dna 60 with relatively little modifications. does the PVA use the dna 40 on board buttons?
I am not sure about the buttons, if they don't, where could I buy the right buttons? And I know he went with a cheaper Chinese charger. Is that hard to change to the Evolv one? -
I have a DNA 40 mod with dual 18650 in parallell. It is that brick of a mod called PVA 40, which the YouTube reviewer "Peg" from Pegasus vapor Academy said he made "For the people, by the people"
https://www.youtube.com/watch?v=MU3GteeXRf8
It reads lower ohm than any other mod I have and had, and it feels like it performing weak. In watt mod with kanthal it's ok, but in TC it's a mess. Unfortunately it have the small dna 40 screen.
What I wonder is if I could swap the old chip with the DNA 60 with small screen? Because the housing off the mod is built like a tank and on my desk it could serve good with proper TC. I like ss 316 single coils the most. Although Nickel and Titan is ok too. The Vapor Shark Flask DNA 40 perform like it should and is a much better vape with NI200 -
Hi. I read about The Therion at GearBest, and under Q's and A's the seller claimed that it was not possible to charge The Therion via USB. "Please use a external charger" it's something among others she wrote.
-
dwcraig1 said:
This is the settings for Steve's Hcigar VT133.
What DNA200 mod do you have?
I have the VT200 with Li Po, same for me? And the mod resistance is? -
txmonkey214 said:
If they are authentic LG's, and they are 3000 mah, it is the correct watt hours. But, this doesn't mean that you will get 22 hours of vaping, between charges. Especially with high drain batteries. They can exceed 30 amps while vaping, if the mod pulls extra amps. I like to charge mine, when they get around 40%, because this is supposed to extend the usable life of the batteries. Letting them drop down too low will definitely shorten the life of your batteries. So, no. Don't keep vaping until you get a low battery message.
Doe's that 40 % "limit" be right for the Li Po in the VT200 as well? -
I have no plans to replace the battery. But what is the correct settings for the original VT 200 battery in e scribe, since it`s not 1300 mah as advertised? Mine are currently set at 12,21 Wh. Is that the correct settings?
-
Ok, then it`s not a proble. I have already all the wires there . It was just different and I thought it was a bug. Sorry and thank you very much. I would also like to se presets like they have on the newer devices. Have a nice day.
-
Hi
I have a Hcigar vt 200
After I installed the SP3 I can`t load spreadsheets from steam-engine. The box who comes uo is just showing ecig profiles. It`s set up to use SCV(excel) I know from the file explorer that there are spread sheets from steam-engine stored there. Otherwise the SS 316 is so much better. So all in all I`m very satisfied.
Greetings from Norway -
I just want to thank Evolv from the bottom of my heart for the new service pack. Now SS 316 is like vapeheaven. And the taste...ohh. Great job. Brandon and co.
-
Answer
-
retird said:
I know my comments don't meet your concerns but....... at the very least SS wire is probably the most "touchy" wire that folks try to use. The fact that the DNA75 seems to smooth it out a bit shows me that Evolv is going in the right direction in responding to the ever changing wire landscape.
Have a great day
Hi
It would be very nice if they at least included the pre installed settings like the Triade dna 200 by Lost vape, and The Efusion mods also from Lost Vape. They have settings pre installed like Ti1, NiFe30, different SS like 316L and 304 and more. Of course the Nickel 200 installed to, so you don`t have to hasle with steamengine for each profile. -
black lace said:
I had simular experiance using stainless, several months ago, i couldnt really get to grips with the coils and csv's, and when i thought i had got somthing steady the juice tasted awful, its very much an each to his own thing,, but having been using this site for several months, the stainless did come up quite often as problematic, not so much now that the new update carries a profile. i'm using kanthal in a dripper right now and as far as tc goes im using a lot of nife30, people must have some extreamly well tuned taste buds to rate one tc material over anouther, but again each to their own..
I have tried to update the firmware, but I dont have any pre installed profile like02 the one Mikevapes had on one of his newer dna mods. Could have been the VT 75? -
How do I choose if I have the TFV4 Stock coils With Titanium? I dont know the wire gauge or number of wraps. Just the ressistance at .32.
Convert a DNA 40 to DNA 60
in Installation and Assembly
Posted
Thank you for that Chunky.
You see there is my big issue. I have to find someone who knows how to solder for me. I could try to open it, take some pictures and let you see the internals. I'm not asking you to do the job here. I think I could hire someone here in Norway to help me out.