whiteowl84

That's what I was getting at. I don't have multiple tickets. I'm still talking to the same guy from before I sent in the first device. If he hasn't gotten back to me by Monday I'll start a new ticket and explain my situation. I vape at 130w or so and dry burn at the same. It takes several seconds to burn through the gunk. Once the coils are glowing in the middle I brush them with a brass brush. With most of my coils 100w makes for a 4 or 5 second wait before any vapor is produced. I do what I can to keep the mass down...I'd like to use less power but over powering gives me better battery life than waiting for the ramp up.

Dead short? There's no dead short happening. These are the same staples I've been firing for weeks now. I don't have any ni200 or Ti. I don't really like TC but when I do use it it's 316l. If I can't dry burn it I can't use it. Since I got my G2 I only use it for TC. Pretty cool to TC an n80 staple coil. It's not dead, it's just not usable. I'll just have to send them in but I don't know if I need 2 RMA forms or if I can just toss them in together. I've had nothing but problems out of them but if Evolv can fix them this time I'd be happy. I really wish HCigar would give me my money back.

Both are saying ohms too low or check atomizer. Thus they will not fire. When I use Atomizer Analyzer it gives me a question mark. I've had both fire staple coils that read 0.07 ohm and my current builds are 0.12-0.08 ohm. I realize they will fix them but so far I'm $210 in the hole for 2 mods that don't work plus the cost of the G2 to fill in the gaps. I wish I had just saved up and gotten a couple parallel mechs. And I waited 4 or 5 days to get my first response. I was panicking. Lol. And I don't feel like that was aimed at me. I haven't bashed evolv and I'm a really advanced builder. I bought these mods for staples and quad core aliens. The only thing that's changed it the fact that they won't fire builds that they did a few days ago. =(

EVolv were the ones that sent it back with a broken down key. The vendor was VAPENW which doesn't do refunds or replacements...I can see why. The daughter board from HCigar is under the batteries. I'm pretty sure the fact that they will not fire is the DNA chip isn't it? I think Help Desk is tired of messing with me because they didn't respond today. They sent me an RMA form but that was for the second one. I'm not sure if I can send both in on the same form. I'll probably do it any way. It's either that or the trash. And about fixing the sticking button...it won't even fire any more so it's moot. Thanks guys...I'll also try contacting HCigar. They didn't respond to the adress on their hompage.

I bought 2 VT133s within a week. The second one stopped working after less than 24 hours. Sent it in. The daughter board was defective and it took about 3 weeks to a month to get it back. When I recieved it I immediately noticed the down key was broken which it wasn't when I last had it. It gets stuck and takes some pressure to release it. Help Desk says to send it back again. I asked if it was possible to refund it and since they don't make mods they said no, just send it back again. They also didn't comment on how to get a refund from HCigar or how to contact them (no response from their email.) Now, about a week later the first one will not fire anything. Either ohms too low or check atomizer. Atomizer Analyzer says "?". I'm at the end of my rope. I can't afford to keep sending them back just for them to break again. I actually bought them to replace my old mods (now dead) and had to buy a hohmwrecker because I needed a mod while one was gone and I knew this would happen. Just cut my losses and move on or is there something I can do? Me and my wife both need a working mod and between these two we don't have one. Sure the silver one works but it's very annoying to deal with everytime you pocket it. Strike that...now both are inoperable.