mackman
-
Posts
31 -
Joined
-
Last visited
-
Days Won
1
Content Type
Profiles
Forums
Downloads
Posts posted by mackman
-
-
Unfortunately my week old Orion stopped responding, emailed a RMA request and 1/2 hour later had it....talk about customer service!!
-
2
-
-
0.25Ω pod will not release...poor manufacturing tolerances? Going to need pliers😆
-
Received my Orion today and the USB cable is a data cable although not the braided/branded one. Go figure.
-
I have had a red one since they were 1st released and it looks and performs as new.
-
-
Positive thoughts and prayers for you Jethro. I am a stage 4 lung cancer( 2 year) survivor...all things are possible
-
1
-
-
Weak 510 spring pressure, poor solder joints, poor atty pin connection/coil connection , many possibilities, frustrating to sort them out
-
non temp sensing coils
-
Like many others I am anxiously awaiting replay. As a long long time DNA user I am fully satisfied/thrilled with the DNA 75C and can customize my vape onboard to get what I already perceive as a perfect hit each time.
-
I had been having problems when starting Escribe getting the message not responding then it would open. I uninstalled and reinstalled Escribe 2.0 SP 9 and the message stopped.
I ran the case thermals on a DNA75C mod and when I tried to upload the settings I get this. I also get this message if I try to change any of the profile settings
-
In regards to asking if it is a new coil each time I read that it was happening for a member only with TI wire. SO I changed to SS 316L and thru several coils it has asked again.
-
James that is correct, SP27 is what is installed don't recall about previous versions.
-
I had the same problem no matter what I tried. Stopped when I locked resistance
-
Just reset the 2.5v cutoff to zero so we will see.
Anyone else get the new/old coil message anytime the mod sits for a few minutes?
-
The problem I have had since the beginning is the check battery message at ~3.40v. I can unscrew/re screw the battery cap and it may be error less for a short while. This is with brand new Sony VTC5 and Samsung 25R batteries. In Escribe battery cutoff is 2.5v. Running a .4 single TI1 coil at 40w and 430 degrees. Really like the ability to dial in the settings from the screen so I just deal with it
-
Vaping Bad thanks for the prompt response
Yes it opens to a folder Evolv>Escribe>Firmware
Although I read where the firmware was included in the 9.30.2015 update I thought there was an update included and had lost my friggin marbles
-
Download and run https://www.dimensionengineering.com/software/SetupES_2015-10-21.exe (51MB standalone installer).
Go to Tools>Update firmware..window opens to select file but can't find it (no firmware update type file)
Windows 10 OS -
Pateyevee I would suggest you go thru the Evolv Escribe interactive training course (http://www.evolvapor.com/guide/story.html). It's a good learning tool for learning to use Escribe
-
black lace: all up to date
vaping bad: no restore or size
Thinking it is a conflict having installed over and uninstalled/reinstalled the Escribe. It worked before and haven't downloaded any programs. Only thing that has changed is receipt of Windows update which I can't control -
Thanks for the reply VapingBad but move is greyed out
-
I open Escribe and connect a mod then open the device monitor. It shows on the task bar but it will not show on the screen. It only shows on the screen by hovering over the task bar icon. The main Escribe page projects fine. This has just started, previously it worked as expected. I tried reinstalling Escribe over the current install and even deleted it and reinstalled.
OS is Win10 -
Upgraded from 8.1 to 10 without problems and running flawlessly. A few tweaks to the settings is all.
-
Yes Windows 10
-
Today it is showing temperature in device monitor. Same mods and atty's that did not show the temperature yesterday. Confused? me too.
freebase nicotine vs salt nicotine
in General Discussion
Posted
Short answer I do and it does