noah

26g/2.5mm/8-10wraps to get around .5ohms/ temp range 370f ~ 450f/ micro coil dry burn to get rid of hot spot using low voltage around 3v with short pulse. I tried 50W, 75W, 100W preheat and they all had same issue so I tried with preheat turned off and got same result. Mod used = VT75 nano, Therion 166 with LG HG2 batteries. I thought it was an issue with my VT75 nano because when I put same coil on my Therion, it didn't have any issue but when I made a new coil and tried it on Therion, it was giving me same issue. I double checked my connection and tried with few different atomizers. So after about 8-10 micro coils, I tried spaced and it works like a charm. TC mode is very confusing and I want to get this right because I've purchased all these different types of ss316l wires such as clapton, fused clapton, stapled, alien, and etc but these issues are holding me back and making me to use them with Power Mode only. If you need more info, let me know

Therion 166 & VT75 nano Does anyone having TC mode issue, such as going over temperature and burning coils and cottons when using micro coil with ss 316L? I'm a big fan of micro coils for my kanthal so I decided to make micro coil for my SS316L and try TC mode. 24, 26, 28 g used. lightly pursed to get a hot spot with voltage around 3v. I let it cool to room temperature, wicking and soaking and ready to vape BUT.... it just burns my coil & cotton by setting up a fire.... I thought it was a mod issue but when I use spaced coil, both mod works fine. Anyone else having same issue???? and how you fix this problem??

Thank you so much. I've tried few and it seems that my mod resistance is 0.004-0.005. I also found out that I'm only having issue with TC mode(mainly using 316L) when I install micro coil. I tried several spaced coil using 316l 28g, 26g, and 24g and both therion and vt75 nano is not burning any cotton and cuts the power properly. Does micro coils make harder for mod to read temperature correctly?? Do you use micro coils for your TC mod??? if so, did you ever had this problem???

Therion - did not save and I uploaded someone else's mod setting... I will try again tomorrow to see if this will work out and if not.. I will post pics so you can take a look at it. VT75 NANO - followed your instruction. but one question. do i have to make a coil?? or do I just bend and connect wire??? btw, below is the result I got and I don't think this is right... Goon RDA clone(24g and did not make coil) - cold 0.421 - raw 0.443 = 0.022 Mephisto V2 RDA (24g and did not make coil) - cold 0.125 - raw 0.129 = 0.004 Narda RDA clone (26g 3.5mm coil) - cold 0.629 - raw 0.674 = 0.045 all waited for about 30 min to reach room temp. what am i missing... hm......

I'm new to TC mode and so far, didn't really had any luck. I'm having an issue with my Therion 166 when I'm using 316L, 26g, 2.5mm 9wraps, 0.51ohm, micro coil. Below are the steps of how I proceeded on Merlin Mini Single coil mode. 0. 316L profile from steam. preheat 0, watt 100, 420F (also tried dropping wattage to 50w) 1. 2.5mm, 9wraps, 26g 316L, Micro coil(to prevent spit back when I vape) 2. 3.0 or less voltage(about 12-15W) to check hot spot. -> let the coil cool down to room temp. 3. wicking -> eliquid After all the set up, before assembling my tank, I test fired to get rid of cotton smell. Instantly, coil gets red, temperature goes over 4000F(screen was reading temp close to 4890 to be exact) and makes fire. At first, I thought it was a issue with my set up so I tried making about 4 different coils, same ohm and trying it on my VT75 nano. On Nano, it didn't burn and did cut the power at certain temp but after 1 day usage, coil was burned. Set up: no preheat, 55w setting. I'm not sure what the problem is. For VT75 Nano, i don't have copper screw, so I researched and set the MOD Resistance as 0.013. I spent more to try and get great TC experience but so far, my cheap eleaf pico 75w is doing much better job.... Please help...

Hi guys, I've been vaping for about 3 years and have been using Kanthal wattage mode only. *** Recently purchased Hcigar VT 75 and Therion 166 hoping to explore TC mode with Titanium and Stainless Steel 316L.*** I've been researching and tried many things by myself and came up with problems and question. 1. Profile - There is about 7-8 basic profile for nickel, titanium, watt, stainless and etc. If i'm using one of the wire, it is ok for me to just use basic profile that is in my device by adjusting temperature to my need? 2. Downloading TFR from STEAM - Since I've purchased SS 316L wire (24,26,28g), I can just select SS 316L from wire wizard and add it to my wire type and use it for all size SS 316L? (graph and numbers seems all same even if I select different size SS 316L) 3. adding profile from General Tab. - from General tab, there is an option to select a wire and below, there is a tab to add profile and it only allow file form of *.ecigprofile. What is this??? I cannot find any info on this.... Or has this been replaced by ADD Wire type??? 4. Pre heat and Wattage setting from Escribe (Ex: 0.5ohm SS316L) - is there a guide that I need to follow pre heat wattage and wattage for tc mode? - As far as I know, TC mode will cut your device off once it goes over set temperature. Does this mean I can put 100W for pre heat and set wattage as 166 and my device will not reach that wattage once it reaches the temperature??? 5. anything else I should know??? Hope to find above answers. Thank you guys in advance for your help.