illogik
-
Posts
33 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Posts posted by illogik
-
-
Theres 3 arrows in your screenshot at point 1. Pointing to Power, Live ohms and cold ohms. Those are the same 3 I selected. I didn't click power set.
-
I know whats up with it lol. I just remember I swapped out those coils for some I got sent in the mail from somebody and they are ni80 so ofc not compatible with tc. Oops!
Battery shot here.
-
I didn't click on the power set option?
How do I turn on those values? They aren't there on my escribe.
I didn't change the battery curve as it's not a lipo mod, it's dual 21700. Should I still be changing it?
-
My hadron pro coils look fine. I plugged it into escribe and turned tc back on for the ss316 profile and saved to device and it works again now but trying the same thing on the Hadron plus it just reverts back to watts as soon as I take a puff.
-
On 6/16/2022 at 7:36 PM, Wayneo said:
This can be one of the most difficult issues to find due to so many different reasons.
Was this a new coil or new wire or a new atty?
Was the coil checked for any hotspots before using, and screws were still a tight connection?
Was the coil installed at room temperature?
Describe the coil and Ω's.
Using Atomizer Analyzer tell me how much the coil fluctuates over a minute.While taking a puff using Device Monitor (and the same 3 fields as below(1)), pause the screen (2), hover your mouse over near the end of the puff (3) and click for that vertical line, and post the full screenshot like I did.
It was an already used coil in an already used tank, both used already on this dna mod.
No hotspots and all screws tight.
Installed at room temp yes.
The coils are a pair of SS316 SSFC's at 4mm ID, 0.16Ω
In Atomizer Analyzer the coil sits at 0.164Ω and every few secs will go up to 0.165Ω briefly then back to 0.164Ω
Here is the screenshot from one of my hadron plus that has this issue. One of my hadron pro's has the issue also but that is a build I did a while ago so I'm going to check the coils first.
-
12 hours ago, CMK aka gwyar said:
Here, too, the question of the theme used must be asked, because in some themes the temperature display is only shown if the chip has recognized the finished coil as temp-sensitive - regardless of the fact that SS316, for example, is set as the material.
I am using Frank65's paranormal, Odin etc theme.
20 hours ago, Wayneo said:This can be one of the most difficult issues to find due to so many different reasons.
Was this a new coil or new wire or a new atty?
Was the coil checked for any hotspots before using, and screws were still a tight connection?
Was the coil installed at room temperature?
Describe the coil and Ω's.
Using Atomizer Analyzer tell me how much the coil fluctuates over a minute.While taking a puff using Device Monitor (and the same 3 fields as below(1)), pause the screen (2), hover your mouse over near the end of the puff (3) and click for that vertical line, and post the full screenshot like I did.
I'll get this done later for you Wayne, kinda busy right now. I also noticed I have more than 1 DNA mod doing this. Will post details later.
-
I've been using SS316 tc mode but today it has changed from the temp setting to watts. The mod is set to ss316 tc mode but the display reads watts where it should say temp. In escribe for the ss316 profile, it turns temperature off. I can turn it back on and upload the settings but when I fire the mod it reverts back to watts again.
Any fix please?
-
Well it seems to still be working fine. Thanks a lot for your help Wayne. Much appreciated
-
3
-
-
Just tried some new cotton which I'm not liking so gonna change back. Will let you know if it still works in a bit once I've done that.
-
Yeah I resampled before firing.
Just checked the pin now and it wasn't exactly loose but wasn't tight either. I tightened it up a bit and it seems to be working ok now. It's letting me save and replay, so far.
-
1
-
-
Well I am completely puzzled now. I stripped down the ragnar. Wrapped new coils and put the deck on the dna mod to remove hotsepots etc before wicking, and I'm already getting the same check atty error. wtf
-
Hmm, might be easier just to rebuild with some new coils then...
Thanks Wayne!
-
Ok, I tried all 3 of the atty's I'm currently using with SS coils. Both my titan v2 and plus v2 work with replay fine but when I put the ragnar back on there, same error when I try to use replay.
-
I just tried my titan tank on there and it lets me save then replays without any errors. I don't get it.
-
Hmm, tried again after typing the above. Had one puff and the save option appeared. I saved and then tried again and it gives the check atty warning again.
-
Ok, I put the atty back on the mod, resampled. Had 1 puff and it showed the option to save. I had another puff (was going to save after the 2nd when it was a bit warmer) and the option to save isn't showing now. It just says 'ready' after all puffs.
-
Well in that case, it has been sat unused lots of times today because I have 3 other setups in use too so I'm not using that one all the time.
I have removed the tank anyway. The mod has been sat without a tank for almost 15 mins now.
-
Same coils yes. Do you mean remove the atty from the mod and leave it sit?
-
I've been using replay for the last week or so since I got my hadron pro but today for some reason, it wont fire when I create a save. Instead it says check atty. I resample the atty and then it fires again but without replay as the previous save gets lost during the process. I can vape on it fine but as soon as I save a replay and try to vape with that I get the check atty warning again.
Any ideas?
-
1 minute ago, Wayneo said:
Yes
Noted. Cheers Wayne.
-
1
-
-
2 hours ago, Wayneo said:
You can use your 3A charger (I use a much more powerful laptop charger) because your mod will only ever draw 2A max.
Wouldn't the 2a and 3a both charge at the same speed then if the mod won't draw more than 2a?
Thanks Wayne
-
7 minutes ago, artisonore said:
I prefer to charge at 0.5 mah (with external LiPo charger up to 4.10V) as I have 3 LiPos and I don't care about time, but less mah, less stress, more life for the battery.
I'd be the same as you if I had more lipo batteries but at the moment this is my only one so waiting half the day (at least) for it to charge isn't so good.
I appreciate your input though, thanks!
-
1
-
-
Nvm! Checked the steam crave site and it says 3a max but 2a is recommended.
Thanks anyway!
-
Could someone please tell me what is the safest maximum charging amps I can use to charge this lipo mod? So far I've just been charging it via my pc which of course is a 1a charge. I have also been using a 1a charger when not plugged into my PC. However, I do have a 2a and 3a charger I could use. Would these both be safe to use?
Thanks
SS316 TC mode changing to watts on its own.
in General Discussion
Posted
I'll check the battery settings out tomorrow mate thanks.
In not sure what steam crave do to the dna boards so can't comment on it.