-
Posts
11 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Posts posted by lupinehorror
-
-
23 hours ago, dwcraig1 said:
i can solder but that's a wee bit beyond my ken.
-
On 8/11/2019 at 7:23 PM, Wayneo said:
With it apart (panel off), did you plug it in and see if device monitor still shows the button being pressed? The actual board buttons are on the fire button side, and wires are usually routed away from them.
sorry for the delay.
this is it apart and connected to escribe. evolv have replied to my ticket and i sent them the same file. 'Buttons: Up'.
cheers.
-
1
-
-
38 minutes ago, Wayneo said:
There you go. In your last printscreen, right there in the middle, see it says Buttons: Up. Then you said you set it to 15, but it fired at 29. Now at 60. Seems/sounds like you have a sticky button, at a minimum.
All 3 actuators/buttons are external to the board. You'd need to remove the panel over the buttons, and clean it ou if there's any leakage or find what's causing the sticking.
Good luck
took everything apart. twice. copious amount of contact cleaner sprayed. put it all back together and it's still the same. the buttons seem fine and are just as clicky as they were before the fault. i knew there hadn't been any leaking and there wasn't. stumped.
-
8 minutes ago, Wayneo said:
There you go. In your last printscreen, right there in the middle, see it says Buttons: Up. Then you said you set it to 15, but it fired at 29. Now at 60. Seems/sounds like you have a sticky button, at a minimum.
All 3 actuators/buttons are external to the board. You'd need to remove the panel over the buttons, and clean it ou if there's any leakage or find what's causing the sticking.
Good luck
very useful. thank you.
-
and i'd actually changed the power, in escribe, to 15W but it fired at 29W.
tried a hard reboot. no change.
also...just noticed. when i put the battery in and switch the mod on the Ws just automatically scroll up to 60 without me doing anything.
-
34 minutes ago, Wayneo said:
After you held down those 2 buttons for a few seconds, could you change the watts?
There are 3 different lock modes on the box. If you start with it not working and then plug in and start escribe - device monitor .......... what does it say down at that very last line on the left hand side? Your pic did not show it. DW's pic shows Mode: Charging, Power Locked.
hi.
buttons do nothing. can't change wattage or anything else. device monitor says 'Mode: Charging'
-
15 minutes ago, dwcraig1 said:
This is the first time that I hear about this particular problem, others have had a problem with mod not coming out of deep sleep or had no connection to battery. Perhaps someone else has some ideas but you should contact Evolv for a remedy.
have done...thanks for your help.
-
-
57 minutes ago, dwcraig1 said:
When connected to EScribe it fires the coil normally?
How about posting a screen shot of Device Monitor while firing? Like this one.
you look familiar from ecf! thanks for replying.
battery left out overnight. nothing changed. here's the screen grab of it firing on escribe
-
all,
hoping you can help. my DNA60 device was fine. next time i used it...nothing. it shows the attached or hold up and down buttons to unlock power. if i connect it to escribe works fine and i can fire it and change settings. disconnect it and back to square one. tried resetting it. still the same.
buttons do nothing. can't fire
in General Discussion
Posted
i did but as i haven't accessed that board i couldn't do anything about it. please see below
just got an RMA from evolv so will be taking the mod apart. will check the button when i've got it in bits. if i can fix it that way it'll save them and me some money.
thank you both for your help and advice. it's not an area where i have a huge amount of knowledge.