Jump to content
Evolv DNA Forum

Badnews69

Members
 View Profile  See their activity

  • Posts

    10

  • Joined

  • Last visited

  • Days Won

    1

 Content Type 

Posts posted by Badnews69

  4. Therion DNA75c BF Temp Control Issue

    in General Discussion

    Posted

    I have a 0.19 ohm spaced dual coil SS 316L setup in my Therion 75c BF, The highest temp I can achieve is 375F at 35w. Even if I put the wattage to max 75W  I couldn't hit 450-480F.  I check on the device monitor, Also the internal mod resistance was set with a copper shorting plug. I got the same reading that was in the mod that the factory had it set which was 0.01

     

    I'm clueless and help appreicated

     

     

     

    Snap1.jpg

  5. therion bf 75c

    in General Discussion

    Posted · Edited by Badnews69

    33 minutes ago, mstave said:

    Using the copper plug, I measured the internal resistance as 0.018,  thought that was high, but the only other dna squonk mod I own is the DroneBF - that internal was 0.004 - but different 510 and different chip

     

    Mine came factory at 0.01 internal ohms and read high, After test with copper plug it read 0.015 which is very small. But the ohm have been straight on the money.  I'm using EScribe  Version 2.0 SP12  International. So my Therion DNA75C is at firmware 1.1 SP27. Use same Escribe for my Therion DNA166 boxes. But DNA boxes are used maybe 6x a year. I have over 100 mods as i'm a collector so none get beat to n sh*t. I switch mods every 2 weeks and run 6 at a time for 6 flavors.

     

    However my ohms don't swim all over the place.

     

     

    Before you put a new ohm value in EScribe I change it to "0" first and upload then put new setting in and upload again.

  6. therion bf 75c

    in General Discussion

    Posted

    My ohms don't float around, I'm running international SP27 firmware on a US  device, However I noticed the word battery at the bottom of my screen sometimes. Just started today. Will figure it out. I was getting new or old atty also. I pulled the atty and tightened the squonk pin and that solved that

  7. therion bf 75c

    in General Discussion

    Posted

    3 minutes ago, mstave said:

    Nick has advised sending it in, resistance jumping around is a known issue with lostvape dna75c mods.

    What the heck is a 11USD Calibration Tool?

    Ohms jumping all over the place isn't good. Ohm just reading off is your atty, or mod resistance or 510

      

    http://smokefreemods.webs.com/apps/webstore/products/show/6619269

     

  8. therion bf 75c

    in General Discussion

    Posted · Edited by Badnews69

    2 hours ago, mstave said:

    I have the same issue with the mod reading ohms 0.3-4 ohms too high and jumping around.   Emailed Nick to ask if I should send it in to Evolv, or just send it back

    What is the factory internal mod resistance in EScribe

     

     

    You can use a 11USD Calibration Tool for the DNA250, 200,75,75c,60 and it will fix it. Takes all but 2 mins, But if the ohms is jumping around like mad then you have maybe a ground problem with the 510, If not the internal mod resistance is off.

  10. therion bf 75c

    in General Discussion

    Posted · Edited by Badnews69

    On 10/17/2017 at 2:16 PM, Azazel said:

    Djlsb said it had something to do with the internal resistance of the Box being wrong and it's like 0.0081 he recommends that you go on escribe and set it to  0.015 mine's been reading my has been reading my coils extremely accurate

    I loaded the international firmware SP27 on my U.S. Therion 75c bf which my default factory internal mod resistance was 0.01 and changed it to 0.015, It reads correct now and the extra features of the international firmware to boot. 

    https://www.youtube.com/watch?v=YG2RudRe7kY

     

    • Confused 1
×
×
  • Create New...