[SS316 Mesh]

36 minutes ago, Wayneo said:

DJLSB vapes has put out some good videos on Reply, TC, escribe, etc. for mods with these boards.

From back in 2017 I said "...  I'll usually vape a new juice in Wattage mode before moving to TC. I have a minty watermelon juice that in TC I totally lose the mint at 420F.  And a peanut butter vape, where at certain temps the peanuts will taste burnt, not the whole juice, just the peanuts. But overall, TC will give you a consistent experience and no dry hits." In other words, a linear/singular taste.

Now (or during the birth of Replay), the brain trust at Evolv said this "As for flavor, different flavor molecules boil and are primarily tasted at different temperatures. .... Temperature control, by contrast, tends to taste 'muted', because the vast majority of the puff is at a fixed, instead of changing, temperature"

pretty much validating my experiences. Enjoy your mod

Thank you so much for all the advice I'm sticking with Replay now that you explained to me how to use it! I think it's way better than what I was getting in temp!

[SS316 Mesh]

Wow it's crazy how accurate this thing is! In wattage mode on my Lustroni had to vape at like 61 watts with the nexmesh SS316L coil to get the hit I like, on this Odin I only have it at 58 watts with a 2 punch boost on replay and get a much better hit. I'm glad I finally took the plunge on this baby lol

[SS316 Mesh]

37 minutes ago, Wayneo said:

That's all correct. Replay gives you the 'dry hit' protection of TC, without the TC. Notice I never once mentioned a temp.

But 'yes' you can also enable that in the SS profile, BUT WHY? 

Oh okay so I go into replay and find a wattage I like then hit save puff? I didnt know that(: sorry I'm slow to understand lol this is my first DNA. 

[SS316 Mesh]

What themes do it the way you say lol I wish mine did unless I just dont know what I'm doing. 

[SS316 Mesh]

2 minutes ago, Wayneo said:

You don't need to plug it in. Just go to that Replay profile. Ideally the material type says something like watt or kanthal. Don't change it. Adjust your watts to what you like,take a few puffs,  'select' the Replay option when you like the puff. Ideally it'll say something like enabled or playing. There should be a cancel or stop option somewhere.

Unfortunately themes are like the Wild West and designers can make them however they please. 

Now see on the theme that came with the Odin this is what it says. When I got to Replay on mod and select it only let's me change the wattage, no temp. Even when I go down to settings and Atomizer it says N/A in temp section. 😞 but I know from browsing escribe that I can select replay in SS316L profile while in escribe. 

[SS316 Mesh]

11 minutes ago, Wayneo said:

Minimum Replay requirements

DNA75C, 250C, or GO

International software installed

Theme that supports Replay

 

Success best practices

Ni200, Ti, SSxxx, NiFe or any TC capable material (wire) as your core wire

 

There are 8 profile slots on every mod. 1 might be called Replay (if you're lucky). 

Start vaping in a profile that supports Replay.

No material file required for straight Replay (as conceived by Evolv).

If you don't understand something written, let us know. 

Okay so do I go into my software when plugged in and go to the SS316L profile and set it to replay with where I have it? It has a Replay profile on mod out of box but from what I can tell it's for wattage mode. 

 

[SS316 Mesh]

Thank you! I really appreciate the help, this is my first DNA mod which I wish now I would've bought sooner lol and my first time vaping in temp control cuz my Asmodus Lustro wouldn't hit right in temp. So I basically just fiddled with the controls and made sure I stayed within the limit listed for the Nexmesh SS316L strip until I found a hit I like. Now I gotta find out how to get it in replay mode. 

[SS316 Mesh]

Well I have my Kylin M on the Odin and at 543 at 62 watts, which tastes good but a little cooler than I thought. However it's a much better vape than I have ever had in Wattage mode, am I doing it wrong by having it at 543

[SS316 Mesh]

Can anyone say what the best temperature settings are for the OFRF SS316L mesh in a Kylin M