Longtail
-
Posts
13 -
Joined
-
Last visited
Never
Content Type
Profiles
Forums
Downloads
Posts posted by Longtail
-
-
OK. Thanks for the reply. I'm waiting for a rfesponse from my local vendor now. Normally he's pretty good with his gear due to being in Thailand. Hopefully he will replace the whole unit for me, he may even want to deal with evolve if he bought direct from them. That is my problem you see. Living in Thailand the importation and sale of vape gear is banned, although vaping is not, and any good caught in transit are confiscated. If I can get a replacement it is better as I don't know yet where he got his supplies from.
If I have no joy I will go to Evolve myself. Thanks again for the help very much appreciated. -
Each cell reads 4.17V with a total voltage showing 12.51V
As far as the Fuse is concerned not sure if I would know the fuse if it bit me on the ass. lol Sorry -
OK so this is what I have done so far.
Disconnected and reconnected battery.
Hard reboot
Reset setting to default.
Reset to Evolve standard in the File tab.
Loaded previous firmware, no change to mod
Updateds to newest firmware, no change to mod
No change in the mod. If disconnected from the USB the screen is dead.
If connected to the USB the mod basically works.
But fire without an atty on and the screen shows the normal check atomizer message.
Attach an atty and then the screen cycles quite quickly from the normal screen for firing to check atomizer and back 2-3 times a second at a guess. -
I have had my VTBox 200 for about a week now and the mod has just died. No screen unless connedcted to USB and even then it won't recognise ANY atty I have. All have been used on it before with no problems, All work fine and fire on other mods.
I have tried install previous firmware, no change. Told it to soft reboot, no change, hard reboot no change.
Is it stuffed or should I be trying something else? HEEEEEEEELP!!!!! -
Ok so Escribe and the mod ARE talking, but so far ONLY in profile 1.
Other than that no communication in the other profiles, but at least it is working in profile 1. -
Mod is a VTBox200. been in use for about 1 week.
When I connect the mod it recognizes it and comes up with the correct device name but none of the settings on the mod are transferred to Escribe. I make changes and upload to the device and no changes are made on the mod.
Anything I can try to fix this? -
Thanks for the link I will get on to it now.
-
Meant to add that this also shuts the mod down so it won't fire at all until I disconnect and reconnect the atty.
-
Sorry if in wrong section but wasn't sure where to put this.
Only just started no DNA200 mods, I have a Vape Cige VTBox 200, and I keep getting the temperature protection error even on a cold atty immediately the fire button is pushed for teh first time. Could this be an issue with the board or, more likely I think, the atty, Bellus \or Goliath V2. It is more often at lower temps than my normal 500F. I am using SS 316L with the CTR from Steam Engine.
Any fix for this? -
Of the posts that I've seen relating to the Lion 1800 mah battery that comes in the Vapecige the actual capacity is around 1250 mah to 1300 mah.
That would definitely explain it then. I have a ticket in to Vape Cige, and although I know they have seen it they haven't yet replied. but these figures sound right to me. Thankyou. -
Thanks for the answer.
The mod is a VTBox 200 by Vape Cige with 3 x 1800 mAh lipo cells.
I will look in to the battery analyser to see what I need to do for it.
Will also check using the Device manager. way as well.
Thanks again. -
Please excuse the basic question here but I am new to ALL TC more to to DNA and Evolve.
Escribe has shown my batteries Watt hours at 15.2, but my box specs tell me that it is 1800mAh. That gives me a Watt hours of 19.something, escribe not available. BUT my batteries show a 4.2V charge on ascribe acress all three cells. Would I be correct in assuming that the 1800mAh for my cells is bogus? or have i got incorrect settings somewhere that I need to fix up? TIA
VTBox200 by Vape Cige Bricked?
in General Discussion
Posted
Just gone back to TC after trying some of the early attempts. I wasn't having a good vape at all then in TC, but now with this board I have to say I will be sticking to it. I can get all I want from it and refine it to suit my preferences much better.
A shame about the board crapping out but sometimes this happens and if I get good back up from Evolve at least I will have no problems continuing using it.