Ken Nutter
-
Posts
71 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Posts posted by Ken Nutter
-
-
Just some cool macro pics I've taken and wanted to share with my vape family. Happy vaping everyone
-
Looks great... Nice work
-
My Opus TC control issues started to minimize after I tightened down everything in/on the 510... I have preheat 150watts/0.25sec/4punch... Keep watts around 100 and temps usually 300-400 range. Any higher I'll start charing cotton on occasion. Hope this helps... Also I have better luck with contact coils.
-
Quad builds in velocity or Stro miniV2 have been my go to. I'm using TI and TC but I have a kanthal in wife's mod and she loves it(as do I)
-
20awg square TI... Ahhhhh its OK... Going to try Clapton TI now that I got more wire and a couple smaller gauges.
-
I know that... Thank you for the reminder though
-
Im not worried till I come to log in and it says "YiHiscribe"... Lol... I about died laughing when Brandon said that
-
Damn them there @ it again
-
I seen the issue yesterday and thought it was fixed. This is from just a moment ago...
-
Very nice build bro
-
Is anyone else getting this weirdness? If a go out then back in it seems to go away... Any thoughts
-
O also I dropped my ramp time to .25sec and 150°f
-
I've had better luck with TI contact coils... Also was have major issues with TC before I checked and tightened up my 510 even more...all of it have a little extra tighten. If I run much over 400 I'll get burnt... Usually around 350 somewhere
-
On the bright side. If it didnt mess the screen up u have an extra screen now
-
Lmao... Literally laughed out loud. Thanks Brandon
-
Turnigy airsoft battety Capacity: 1200mAh Voltage: 3S1P / 3S Cell / 11.1V Discharge: 15C Constant / 25C Burst Weight: 94g (including wire, plug & case) Dimensions: 128x17x20mm (Each) Balance Plug: JST-XH Discharge Plug: Mini-Tamiya (Mini Molex) Would this battery be sufficient? The lower C rating has me worried but I did read an article in here before talking about C ratings being iffy from manufactures. So any thoughts? Thanks, Ken
-
I have same issue alot of times... Check your 510ground connection. On your Atty. I have an opus200 the ground really shouldn't be causing an issue for me because of board grounds to case and the ground wire... But I still have it act up... The ground is soldered good... But it still acts up. So idk. Just check it out make sure it all looks good jiggle it around. I had alot of issues with same thing. Then it just started working right again
-
Velocity, Hobo v3.1, Stro mini are ones I know of that have that post design
-
O yhea sorry bought dirty coils. Not as bad as it looks in pic
-
First time I actually thought... "What am I doing???" To much... Lol. Quad parallel 7wrap TI around 2.5mm reading in @0.03
-
Have you tried the "acetone smoothing" technique for 3d prints? Wonder how well it works
-
If I did tryed it in the lemo2 I was going to pack the crap out it...lol. I made a nice very in my velocity but ran the wick through the coil
-
Instead of paint you could do a mydipkit and that would probably look amazing. I definitely like the design looks cool
-
So weird I just was messing with my lemo2 today for 1st time in awhile... Drilled out airflow wholes in bottom and juice feed wells some... Yhea I put an RDA back on... I'm hooked on quad coil TI build and airflow. I did think about trying a TI chimney build in lemo2
Help & Advice Please
in General Discussion
Posted
My Replay settings. It has ran everything amazingly.
General Tab
Boost: On 5
Warmth: 5
Material: Watts
Mod Tab
Replay: Allow Dubious coils
I will typically guess about were my build should run wattage wise. My first puff is normally a little cool(that first puff should be slightly cool) but as heat builds up the 2-4 puff will be amazing. Then click save puff. And the device will make any necessary adjusts to recreate that puff.
Have used this with SS, TI, NIFE 30.
My normal go to build is dual SS fused clapton's(24awg cores 34awg wrap) 6 wrap 3.5mm center OHMing in at about 0.9ish. Running about 120watts with the above replay settings.