[Evolv reference case]

Dimensions of 950/1300? I know I've seen others ask but I never saw an answer posted.   You can fit a maxamps 1850 in nearly the same space as a turnigy 1300-1500.  

[Using Wh output from battery analyzer -- showing 100% charge at 12.3-4v]

I did have it on max recharges (I normally use max puffs).  It may just take a hard reboot to switch it back.  I'm trying to duplicate the problem.

[Using Wh output from battery analyzer -- showing 100% charge at 12.3-4v]

I am curious if anyone else notices this....  

I ran battery analyzer several times with long cooldowns in between.  Every time I run it I get about -1Wh from what the battery is rated for (Maxamps 1850).

I will see 100% charge when the pack voltage is 12.3-4.  

I changed the WH using the calculator and the battery % goes down to ~94% which seems right.  I will run analyzer again... this specific mod has around 1months use on it.  

[Max Charging Amperage? Which Wall Adapter to Use?]

One note I've noticed.

If you use a "Charge/Power only" usb cable on a PC you will charge at 1amp.  Typically with a data cable you charge at 500ma (1/2amp).

[Feature request: New set of "Fields" in screen tab.]

I know there is a thread about showing TEMP instead of WATTAGE while in temp mode (or at least an option to).

In addition (or alone) I would LOVE to see a third set of "fields" -- temp mode fields.

 
These are generally my default settings.  When I use a temp control atty I manually go in and change the default fields.  Wouldn't it be great if there were default fields for when the device is using temp control?

Make sense?

 
Edit:

Temp Field 1: Wattage
Temp Field 2: Temp
Temp Field 3: Last Temp

Assuming the Temp/Watt swap happens that is being requested by many.  

[Feature request - swap Temperature with Watts on screen and controls]

I would LOVE to see this.

I don't use temp control very often.  So I have to remove it from my "fields" otherwise I have - - - for temperature.  It would be nice if the device is not in temp control mode to put the user selected field -- if it is in temp control mode display wattage.  Sort of how the RX_Clone is setup.

[The little screen ribbon who could.]

I have two screens one had a green protection tab the other has a red tab.  The cable looks different but I haven't tested to see which is tougher.  I am super super careful with screens right now

[Place to share Battery Test Results.]

I'm also curious which enclosure "Bob" was able to get a MA 2800mAh into

I will be posting results tonight.  I ran 5x tests per battery type.  I did see more mAh firing at a lower wattage with a 2.5v cutoff but not at 100w/2.5v.

[Place to share Battery Test Results.]

I see that now.  Looks like when the sag hits the cutoff it's stopping the fire which is expected.

I am testing several batteries... I think all are already on the list but I have multiple of each and I'm doing breaking them in first the proper way etc.

Looks like some folks doing tests on 18650's are using 2.5v cutoff.  I wonder if that would skew results vs/on lipos?  It might be a useful field to add to the list if nothing else.

PS: That's an insane block of aluminum  Have you checked temps on the resistors?  

[Place to share Battery Test Results.]

Are you guys firing until the soft cutoff hits or what?

[510 99.9 pure copper Mod resistance tools]

Sent an email to you.  Very interested in 1-2 of these.  Thanks!

[Evolv logo (vector or high res) anyone?]

That logo is what I'm after.  Vector or high res.  Everything on google is rather small.

[Evolv logo (vector or high res) anyone?]

I'm sure it's posted somewhere but I can't have it.  Does anyone have the evolve logo in vector or high res format they wouldn't mind sharing?  Thanks!

[Temperature Control not working at all.]

I don't use temp control much (or at all because it's never been a good vape for me) but I picked up a Smok TFV4 TF-STC2 coil for kicks.  I have to hard reboot through escribe to get temp control to work at all.  It may just be this coil but at 60w temp set at 420F I don't even reach 200F.  

I tried everything but the only thing that made it kick into temp mode for me was the hard reboot.

[Problems with Lipo 3S first Installation]

It happens  That's how you learn.  I had to keep looking at your setup to be sure it was backwards.

[Problems with Lipo 3S first Installation]

 

[Problems with Lipo 3S first Installation]

Test your balance plug with a multimeter.  That red wire should be your battery positive.  The neg wire is on the opposite side.  Why would a company use a red wire for a negative side?

Unless if that brand of lipo manufacture doesn't follow standards you have it hooked up backwards.  

My money is on your balance plug backwards.  Does nobody else see it??

 

[Problems with Lipo 3S first Installation]

Looks like you have the balance connector on backwards 

 

[Feature request, setting increments]

+1 for feature.  I almost created the same thread.  Custom increases would be nice... even 1w feature would work for me.

[Early Firmware and EScribe Suite Discussion Thread]

I had to manually install the latest.  I saw there was an auto update and installed that -- but it must not have been the latest (or something).  Thanks!

[Early Firmware and EScribe Suite Discussion Thread]

Where is this located (it's late I might be looking over it)?

(2) configurable number of clicks to lock the DNA 200

Cheers!

[Voltage up/down.]

Right.  So maybe instead of saying it's a bug I'll say it's a feature request?

The buttons should change with the screen orientation imo.

[Voltage up/down.]

I never noticed that.... I'm guessing the DNA30/40 models I had were so small it didn't bother me to use it in the "left" orientation.

It's just a little thing that nags me.  When asked "new or existing coil -- press up or down" I'm always confused.

[Voltage up/down.]

I've noticed when you switch the screen orientation to 'Right' the up/down buttons remain the same.  Maybe I missed an additional setting for this but I wanted to let someone know in case it's not intended to be this way.