Jump to content
Evolv DNA Forum

Milkweed

Members
 View Profile  See their activity

  • Posts

    14

  • Joined

  • Last visited

    Never

 Content Type 

Posts posted by Milkweed

  2. VT200 wont fire..!!

    in Batteries and Charging

    Posted

    VapingBad said:

    I am no expert, but I would expect to see one or more cell at a low voltage and one or mores voltage sag excessively when you press fire, but if it's bloated I would just replace it anyway.

    Yeah...i'm still getting it replaced no matter. My only worry is if it still wont work with a new batt. I come from a place where evrything is almost impossible to get. But thanx for your input anyway.

  5. VT200 wont fire..!!

    in Batteries and Charging

    Posted

    My device is almost a year old and recently cant hold a charge for long. I was about to get a replacement battery but something happened yesterday night. After re-wicking my Mage RTA, put some juice in it and fired it up...that's when it happened. Screen went blank. For a moment, I thought it was a blown fuse but the screen came back on a minute later. And from then on, the mod would just restart whenever I fire. Screen would go blank and come back right on. Could it be just a bad battery? Cause I checked the fuse and it was still good. All the settings are gone too.

  10. TI1 & KA1 clapton build

    in General Discussion

    Posted

    I kinda thought so after keep tinkering with it and reading that part again and again. Too bad I had to return to my normal dual Ti build. TC was all over the place and my juice were turning brown. You know how they taste like when that happens. But I'm gonna try it again soon. Thanks for the help @Mad Scientist.

  12. TI1 & KA1 clapton build

    in General Discussion

    Posted

    Mad Scientist said:

    I've used dual claptons wrapped as you describe. I found that the TCR is lower than just plain Ti. You may need to adjust your TCR down by about 0.0005. I would not make any adjustments to actual cold resistance (it is what it is). If you're sure its running too hot on a stable build, reducing the TCR will reduce the temp. Steam engine is pretty good but not always perfect, and the exact wire you have may differ from what steam engine thinks both in resistance per length and TCR. Also keep in mind that a good set of claptons will tend to produce a hotter vape.



    Let me get this right. So if my TCR was 0.006 I have to bring it down to 0.001 or just 0.005? And I think you mean 0.005 as the range is only 0.001-0.01. I also noticed in the temperature control results equivalents tab, it mentioned "To match it on a mod set to Titanium 1, adjust the temperature to ~210°C or ~410°F." and so I did. Seems a lot better than before. It was at 450F previously. What is this Equivalents tab suppose to be for? Oh....and thanks for the help.

  13. TI1 & KA1 clapton build

    in General Discussion

    Posted

    So I claptoned a 32g KA1 wire around a 26g TI1 wire. I saw a post somewhere on this build. I did 7 wraps over 2.7mm ID dual on my TFV4 clocking in at 0.24ohms cold. Got onto steam engine, parallel, clapton on both, input all the figures in but the resistance came out to 0.16ohms. Should i be using this to upload into my mod? Cause I did and the temp was way off compared to my full Ti build. Tank got rather hot after a couple of puffs. I thought it would be rather dangerous to continue. What am I doin wrong? Should i wrap TI1 over KA1 instead? Should i adjust the numbers on steam engine such that i get the same resistance as my build? Appreciate if someone could shed some light. Pretty sure other users are looking into this too. Thanks.

×
×
  • Create New...