[VT200 Mod Resistance (SS 510)]

Don't fire the mod when you are shorten the atomizer!

[Another board that wont charge the battery]

Try to align the batteries properly
 

[More Useful to Show Voltage or Amps?]

I think to show the current is useless. I switched from Volt to Last Temperature

[Temperature Control not working at all.]

I think you've made something wrong. You use a Reuleaux that i can see from ECF.
Be sure to run the latest EScribe Software and load the latest Firmware according to:
http://www.wismec.com/product/reuleaux-dna200/
You can also load the setting file.
First you can control the resistance of your atomizer with Atomizer Analyzer.
If you change settings don't forget to klick Upload Settings to Device.
Another method is to go to Device Monitor to control your Settings.

Try it and be Patient, it's worth  

[VT200 won't wake from sleep]

Did you checked the balancer ports?

[VT200 won't wake from sleep]

Why did you swap the lipo batt?

[Feature Request: Puff time cutoff option]

I think the 20s puff cutoff is a bit too Long.
I would prefer 10s, but i can't change this in EScribe

[VT200 Serial Numbers]

Gold coating over stainless steel is the worst for the mod resistance. I prefer my brass connector #1818, no issues 

Are the threads also goldplated?

[Early Firmware and EScribe Suite Discussion Thread]

Which operating system do you use?
Can your USB cable provide data transfer?  

[Early Firmware and EScribe Suite Discussion Thread]

I've had no problem to install over an existing version under Windows 7  

[Power Off Option]

Set Screen -> Charging Brightness to 0%

[Early Firmware and EScribe Suite Discussion Thread]

Is it possible to show a live view from the screen of the display that isn't attached
This can be useful for testing a mod without an attached display or with a defective display.

My display is dead and so i wish a software screen for the missing display.

[Early Firmware and EScribe Suite Discussion Thread]

Another bug in the 8/5/2015 EScribe Version:



Sorry, it's German

If i activate debug with 7-click on Evolv Logo then all is ok.

[Early Firmware and EScribe Suite Discussion Thread]

Thanks a lot, James

[Early Firmware and EScribe Suite Discussion Thread]

When i push the Get Information Button i see this in Windows 7:



It's the 8/4/2015 EScribe Version.

[Feature Request - Escribe software]

John said:

Speed4mee, you can take a screenshot on the Screens tab. 

What i mean is a live view from the screen that isn't attached

A software substitute for the missing display.

[Feature Request - Escribe software]

Is it possible to show the actual screen in the Device Monitor. It's useful for a defective or not attached screen

[Trade ya!]

I've just inspected my dead display with a microscope. By bending the ribbon cable near the display some wires are broken due to the sharp edges of the glass.
This was the death of my display.

Which can also apply to the Hana V200. The sharp bend, near the glas, is also good to see in the photo from KTMRider..

[Be careful with that Display!]

I've just inspected my dead display with a microscope. By bending the ribbon cable near the Display some interconnects are broken due to the sharp edges of the glass.
This was the death of my display.

[Trade ya!]

I also take a beta unit too and would assemble it myself

[screw stays/spacers for board]

yeah, bolts and nuts

[screw stays/spacers for board]

You can also use nuts, so you can adjust the hight according to your liking 

[Mod assmbled but screen not working]

Thank you, John

[Mod assmbled but screen not working]

No other display available I think i've bend it too much by assembly. The cable is right fitted.

[Mod assmbled but screen not working]

I've made a transfer from my function mod (see Let's see your 200's! #55) to my new aluminum case. Unfortunately my display is dead  

The mod fires, all functions via EScribe are ok. What can i do?