joseph1203
-
Posts
20 -
Joined
-
Last visited
Never
Content Type
Profiles
Forums
Downloads
Posts posted by joseph1203
-
-
when was the battery vheck appeared on you screen in what battery % you can consune all the battery life down to its 5%? if the said cut off reachesWayneo said:... this is a confusingly labeled 3000mAh battery with only a 20A continuous discharge rating (CDR) - from the master. And NOT on his recommended Battery List 9/17/2016
-
joseph1203 said:
hi sir vaping bad ive notice when my battery was down to 35% battery check appeared. also while in battery analyser ive notice that my 2 cells reading was are 2.8V below when firing. my question is, is it normal now or any issue on my mod or cells? the cut off reaches however i have 35% more battery life and i need to charge right away even if i have 35% battery life?
-
hi do you have a video on how to disasembled the therion 133? procedure and step by step.Yph said:Last night it happened to my therion 133 DNA 200. The device just shut down automatically, I plugged it in to USB escribe and it said check battery. One of the cell is not detectable, I tried to reset and hard reset or change the battery from 3 cell to 2 cell still no luck. This morning, I decided to disassemble it. Found the problem of my therion 133. One of the cord that connected to the battery is not attached (there are 2 cords, red and black and in my case the black one). So I managed to fix it and now it's working as usual. Semoga bisa ya agan agan yg dari Indo. Dibongkar manually saja. Kalau masalah dari chip nya aku rasa ga ada. Oyah untuk menyambungkan lagi kabel nya, jelas ya butuh soder dan kawat nya dan untuk therion 133 harus dilepas deck kayu kiri kanannya. Good luck.
-
do you have curve in awt? kindly share because my spare battery is awt same as to you. is it correct if Mah is 3000?Alvon said:Hi Guys,
I just bought brand new Therion DNA133, but when i plug the 2 (AWT RED 3000mah 40a) 18650 battery (Fully charge) the battery indicator on screen is showing that is empty. but the mod it self is fully functional.
Can you guys help me to solve this issue? because i think that is only problem on the EScribe setting. below is the screenshot of my current setting.
Thank you
-
thanks again sir i'll update you once i test the batteryVapingBad said:The soft cell cut-off is set on the mod tab, it doesn't show as such in DM, IIRC you already said yours was set to 2.8 V so look in DM to see if one cell is sagging that low when you take a puff. If it is just one cell swap their position and see if the same cell # in EScribe is sagging to 2.8 V then it is that connection, if it swaps to the other cell (the same battery) in EScribe it's the physical battery. If both are sagging that low it could be weak batteries or connections, those LGs aren't the punchiest battery but they should have no trouble at 60 W at 50% charge.
-
thank sir. i will wait for the result of the test.ChunkyButt200 said:you'll never get the calculated 22.2 watt hours from 2 LG HG2's. even if they are REAL, brand new, high quality HG2's, the real world watt hour/capacity would be closer to 18-19 watt hours. "check battery" means one of your cells is hitting your "cell soft cutoff" limit (2.8v in your case). if i have time tomorrow, i will run "battery anlayzer" for you with 2 LG HG2 cells and post the CSV/watt hour/Cell Soft Cutoff.
-
curve is for 3 cell. im using 2 cell. btw thans for the update. but how can i see on mt device monitoring if there's ant abnormalities in my mod or power?black lace said:No i only use lipol, You could do a search unless someone els inputs, i did a quick mobile search https://forum.evolvapor.com/topic/67896-topic/?do=findComment&comment=911196 .... may be of interest, i dont know i only put nicads by dna40's, You can watch how your power is performing in relation to your coil in device monitor, Right..
-
also on your device graph wheres the cell cut off be located?joseph1203 said:ok sir i'll let you know if i already done it and i will screenshot it. did you find any issue regarding my screen capture of my device monitoring?
-
ok sir i'll let you know if i already done it and i will screenshot it. did you find any issue regarding my screen capture of my device monitoring?
-
How can i test that power ramp up'? Also can you provide me the csv of lg hg2 curve?black lace said:Am not an expert on your battery setup, but your wattage does constantly change for a steady power flow, it may look all over the place on the mod screen in real time, but in device monitor you should see a steady controled power ramp up, even if your not using a temp setting,,, allso what wire are your coils made from??
-
VapingBad said:
Did you look at the cells under load (when firing) in Device Monitor to see if one is hitting the 2.8 V cut-off?
that my battery profile under device monitor. how can i test the one that you've said?
Did you look at the cells under load (when firing) in Device Monitor to see if one is hitting the 2.8 V cut-off? -
not yet sir im on the office right now. i will tell you later once i got home.
-
hi sir i already done it. no issue at 510 and contsct however still sameVapingBad said:Isopropyl Alcohol, Rubbing Alcohol, Electronics Contact Cleaner or Mentholated Spirits and a clean rag.
pls help sir
-
VapingBad said:
Firstly by cleaning the contacts then just checking for anything loose.
thanks sir. i'm a newbie here how can i clean and check if there's any loose? -
VapingBad said:
It could be the batteries are not making very good contact look at the cell levels in Device Monitor when firing to see if one is hitting the 2.8 V cut off.
how can i know if the contacts is good? but if fully charged it seems okay. however when it drops to 50% problem occur
-
dwcraig1 said:
Escribe will show what the voltage of the cells are under load. It sounds as if the board is not getting good power. Might be the batteries, might be bad connection(ect.) of battery contacts to battery. Might be bad solder joint somewhere between batteries and board.
hi sir, please help me with this.
-
hi guys, thanks for the response.
how can i fix this issue? any recommendation/suggestion?
i don't know how to dissembled my Therion
help me up guys. this was very disappointing -
Im therion 133 user my battery are (2 18650's) LG Choco married with battery setting of 22.2 Wh, 2 cell,7.4 voltage. With cell cut off 2.8V
Reading: .25 ohms, dual coil. spaced fused clapton,
RDTA: Avocado 24 new
Queries:
#1. Every time my batteries discharge at 50%, my wattage was unstable. It keeps changing and unable to reach my desire wattage (ie. im firing 60W but unable to reach) what will i do?
#2. Every time my batteries went to 50% sometimes unable to fire. "Check battery on my screen" is my mod was damaged? my batteries are 2 weeks old
Please help guys.
Appreciate your swift response. Thank you! -
Im therion 133 user my battery are (2 18650's) LG Choco married with battery setting of 22.2 Wh, 2 cell,7.4 voltage. With cell cut off 2.8V
Reading: .25 ohms, dual coil. spaced fused clapton,
RDTA: Avocado 24 new
Queries:
#1. Every time my batteries discharge at 50%, my wattage was unstable. It keeps changing and unable to reach my desire wattage (ie. im firing 60W but unable to reach) what will i do?
#2. Every time my batteries went to 50% sometimes unable to fire. "Check battery on my screen" is my mod was damaged? my batteries are 2 weeks old
Please help guys.
Appreciate your swift response. Thank you!
Need help! Therion 133 new user
in General Discussion
Posted