Recommended Posts

Hello together,

 

my Paranormal 75c shows Check Atomizer or No Atomizer when an Atomizer is installed. The tested Atomizers work on all of my other mods! When I take out the batteries and wait for like 10 hours it works for 10 Puffs and then the problem comes. It isn't saying something like too hot or something else before the problem comes. I tried to downgrade it to very old Service packs and deleting all the settings on the mod but nothing helps. Please help me because I don't know what to do.

 

With best regards 

 

Robin6236 

IMG_20171225_153143.jpg

IMG_20171225_153232.jpg

Share this post


Link to post
Share on other sites

The Paranormal's have been having issues due to LV using a loctite compound on the threads of the 510 connector. This could very well be causing the problems you are describing. You can read about it & a fix here....https://forum.evolvapor.com/topic/69140-paranormal-75c-resistance-too-high-fix/

Or you can open a ticket with Evolv & let them guide you...https://helpdesk.evolvapor.com/index.php?a=add&category=1

 

Share this post


Link to post
Share on other sites

Yeah, I thought so too but I wasn't ready to void my warranty. I send it to Evolv and they told me that some Paranormal Devices, in particular, have this problem. It is just hard to guess if it is a hardware failure or a chip failure. I thought it was a cold soldered point but that can't be because it works perfectly for like 10 puffs after 10 hours without batteries.

 

Still thanks for your help.

I just thought it would be the best way to send it to Evolv because they are pros.

Share this post


Link to post
Share on other sites

Hi there!

New mod was delivered to me half an hour ago. I've unpacked it screw the atomizer on top of it and I have this very same problem.

"Check atomizer"

I've tried with two different tanks which on the other mod I have work properly.

On the device I can't even measure resistance in escribe software it says "failed to measure coil Ohms"

Atomizer analyzer only show mod resistance 0,004 ohms and question mark sign on atomizer resistance

 

Device is brand new and it says service pack 25 is installed.

 

Anyone has any ideas or should I contact the seller?

kind regards

Share this post


Link to post
Share on other sites

Sounds like there is a connection problem between the board & the 510 connector...seems it is new, I would contact the seller about a warranty exchange...

Share this post


Link to post
Share on other sites

If I recall correctly the Mod Resistance value shown in the Atty Analyzer is just the setting your device is set at rather than an actual live reading....  You can check the device setting in the Mod Tab/Electrical tab and yours is set to 0.004.... If you change the setting to 0.003 and upload it then the Mod Resistance in Atty Analyzer will change to the new setting you just changed.  In short, there is no atty or no tool screwed into the 510 thus you have a question mark.....probably a connection issue with the 510 connector or wiring to the 510 connector is my best guess without having your device to troubleshoot....

As @giz_60 noted to contact the seller or start a ticket with Evolv... good luck.... let us know what you find out...

Share this post


Link to post
Share on other sites

It doesn't matter how I set it manually result is the same. 

here are some photos for better understanding.

 

This is from escribe "general" tab > measure ohms

Normally you get real time resistance reading from this. (other two DNA75C devices I had in the past) 

measure_error.jpg.28d91eca8c938b322ebffd1cb2ab7bc5.jpg

Atomizer analyzer also reads real time resistance continuously

analyzer_error.jpg.66070d511c663963b6f662b83a2b7ba0.jpg

 

I also suspected 510 connector, but there is a difference with atty installed or removed ...

without

IMG_20180104_145640.thumb.jpg.f0faca4e87352d8b3550fa4bde20d62c.jpg 

 

with

IMG_20180104_145702.thumb.jpg.1f0cfcc30a0934ea930791a79c9cbd11.jpg

measure_error.jpg

analyzer_error.jpg

Share this post


Link to post
Share on other sites

I guess you did not want to do what I mentioned.... A tool is needed to set Mod Resistance thus the Atty Analyzer Mod Resistance is not a live reading as far as I recall...

From your last post it failed to measure the ohm's.... my best guess is still a connectivity issue....  is there a good connection from the atty 510 to the device 510?  What atty's are you using.... some atty's can give this issue also by their design...

Share this post


Link to post
Share on other sites

I've tried few atomizers. 

Once again on other two DNA75C devices I had atomizer analyzer is showing real time resistance. 

I actually ordered two identical mods, the other one for my friend and that one is working as it should. 

Guess I've unpacked the wrong box. :)

Edited by krucymucy

Share this post


Link to post
Share on other sites

The .004 is NOT a live resistance reading, but rather what the Mod Resistance that is set at via Escribe...@retird was trying to get you to set it to 0 to show you that

Mod Res.JPG

Edited by giz_60
Edit

Share this post


Link to post
Share on other sites

Got my Paranormal back from Evolv for a week now. Everything working fine since. It was most likely a hardware malfunction. Also no problems with the service packs and so on.

Thank everybody for their answers. Have a nice day

 

Robin

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now