Jump to content

Search the Community

Showing results for tags 'repair'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Resources
    • Themes and Custom Screens
    • EScribe, Software and Firmware
    • Manuals, Instructions, and Tutorials
    • Replay and Atomizers
  • Reflex
    • General Discussion
  • DNA Cricket
    • General Discussion
  • DNA 250 Color
    • General Discussion
    • Modders' Forum
  • DNA 200 and 250
    • General Discussion
    • Installation and Assembly
  • DNA 75 Color and 100 Color
    • General Discussion
    • Modders' Forum
  • DNA 75
    • General Discussion
    • Installation and Assembly
  • DNA 60
    • General Discussion
    • Modders' Forum
  • DNA Go
    • General Discussion
  • Technical
    • Batteries and Charging
    • Connectors, Components, and Accessories
    • Report a Bug
    • Researcher Forum

Categories

  • Theme Park
    • DNA 60 Small Screen
    • DNA 60, 75, 200, 250
    • DNA 75 Color, 100 Color, 250 Color
    • DNA Cricket
  • EScribe
    • Atomizer Profiles
    • Custom Materials
    • Settings
    • Translations

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


Found 6 results

  1. I have a lost vape halycon that needs the board replaced and probably the 510. The board replacement is straight forward but as for the 510 does anyone know of a replacement I can source? The plastic board holder is in rough shape too but I can make it work hopefully. If anyone has disassembly pictures or tips I'd appreciate it
  2. I have a SqEvo, that I'm looing to repair, and I'm wondering if the wire used in it's original construction is appropriate. It appears to be 18 gauge solid core enameled wire. The mod in question has 10.8 hours on it according to EScribe and I suspect friction of the battery positive wire rubbing against the 510 while the button was being pressed, is the cause for the enamel being burnt off the wire. Originally I was going to just desolder the Battery positive and put heat shrink over it, but then I started questioning the gauge of the wire used on the 510 + and the board ground. Is 18 gauge solid core wire adequate for a DNA 60 positive 510 and the ground connection? I've been looking through the Evolv datasheets and I'm left wondering, Did Evolv under or over spec the Wire for the DNA 60, DNA 75, DNA 200, and or the DNA 250, as they all have the same Specs? I'm not an electrical engineer, so any insight you can offer would be appreciated.
  3. There is probably no hope, but my fire button is sticking and it means I don't want to use my Therion as I'm worried something will happen. Does anyone know a way to fix this issue?
  4. ***in abscensce of anyone ending up providing sourced material, I'll leave a poll for those that don't know as well as to if you believe they would service the device or not. -- Bottom line is I'm not sure if I'm having battery issues as of late currently, or if I'm just vaping eayyy more than usual. (It has been, atleast since I've started to notice, just since upgrading my Original v2 'DNA Go' , to the 'Plus' firmware, and have begun using a little bit higher wattage) If my queries on the forums, & personal tests in device monitor, show that I do need to have it sent it to be serviced. ×How likely is it that it will be denied for their second "Rejections" criteria 'normal wear and tear'? , I ask because I have like, the most minor of scratches on one or maybe two of the edges, however; what I need serviced is completely unrelated, these are small scrapes from me holding it, I need the battery and/or port serviced. And 2nd: Is there anything in 'Escribe' I can change that would invalidate my warranty also?? I.E. 👇 I want to change the, whatever its called, 'maximum puff time' from 6 seconds to something more like 10 or 12 so I can hit the lower wattage longer than the higher for harder for coil BUT I know that's after turning on either researcher or 'manufacturer' options. (that second one sounds an awful lot like a form of invalidating your warranty through 'altering the software or firmware of the device' in a non consumer way? 😬 TL;DR: will super minor scratches (attached) invalidate my warranty request? Especially for something unrelated? (possibly battery/port) & Any settings in Escribe I could change (like manufacturer options) that would result in invalidated warranty? And what are they? (want to change puff time length from 6 seconds to 10) (also anyone know why the selection in escribe is to set puff time and it gives you a drop down with selections in seconds from 0 to 10? (OK I can't attach pics for whatever reason. But imagine literally the lightest of scratches maybe a mm across on two opposing corners only damage.)
  5. Hi, I have a Therion DNA75 and since a while I discovered that the outer battery (the one you put in last) is not discharging. So I only can use the mod with 1 battery now. My question is, is it fixable ? Is it difficult to do, or do I need special tools for that ? I still love that mod and it was not cheap when I bought it, so I like to get it fixed. I am an IT-System Electronics by profession, so I think I can handle some wire fixing if that is the problem. Also, is there any information out there how to open/disassemble that thing to get to the needed area ? Maybe some graphics/manuals ? Thanks in advance for any help on that !
  6. I can't figure out how to have my rolo repaired by wismec so I was wondering if there is a part for the 510 adapter. The spring is sprung and in the process I stripped the threads taking my tank off the mod so I double screwed myself. If anyone has a recommended part for replacing that I would be very grateful.
×
×
  • Create New...