Jump to content

Search the Community

Showing results for tags 'lavabox'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • Resources
    • Themes and Custom Screens
    • EScribe, Software and Firmware
    • Manuals, Instructions, and Tutorials
    • Replay and Atomizers
  • Reflex
    • General Discussion
  • DNA Cricket
    • General Discussion
  • DNA 250 Color
    • General Discussion
    • Modders' Forum
  • DNA 200 and 250
    • General Discussion
    • Installation and Assembly
  • DNA 75 Color and 100 Color
    • General Discussion
    • Modders' Forum
  • DNA 75
    • General Discussion
    • Installation and Assembly
  • DNA 60
    • General Discussion
    • Modders' Forum
  • DNA Go
    • General Discussion
  • Technical
    • Batteries and Charging
    • Connectors, Components, and Accessories
    • Report a Bug
    • Researcher Forum


  • Theme Park
    • DNA 60 Small Screen
    • DNA 60, 75, 200, 250
    • DNA 75 Color, 100 Color, 250 Color
    • DNA Cricket
  • EScribe
    • Atomizer Profiles
    • Custom Materials
    • Settings
    • Translations

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start



Found 7 results

  1. Version 1.0.0


    I tweaked the settings on my lavabox M DNA 75 chip after running the case analyzer. Please post your changes/ comments. Variables: Lavabox 75 M - DNA 75 Chip Geekvape Ammit single coil Stainless Steel 26 gauge (from Master of Clouds) Sony VTC5 Battery
  2. Hello, I'm new to vaping and new to the forum. Just picked up my first mod (lavabox M) and trying to find a kanthal setting. Im using an Aspire Cleito atomizer which has kanthal. Any help? Any suggestions on other sub-ohm tanks to try? I look forward to learning from the group and hope to contribute when my vaping knowledge increases. Thanks in advance.
  3. Version 1.0.0


    These settings contain the default presets for the Volcano Lavabox DNA 200 using the 1300mah LiPo battery.
  4. Version 1.0.0


    These settings contain the default presets for the Volcano Lavabox DNA 200 using the 900mah LiPo battery.
  5. i recently have been having problems with my dna lavabox 200. the mod currently has 97,222 puffs, original battery. tested out the battery with my lipo voltmeter in which all 3 green leds light up indicating the lipo is good. the screen only comes on when the fire button is held down and right after letting go of it the screen turns off. ive checked all screen settings and ive tried to change them and still having this problem. please help -thanks
  6. Hi All, Kinda new here. I've lurked around and searched for answers but I am at a loss. I am having a very hard time getting the Lavabox m (DNA 75) to vape properly at any temperature below 520 Fahrenheit. I have tried several batteries, atomizers, coils, and wicks, including factory made coils. I have also tried several different juices (though mostly 70/30). I can usually get a great vape for about 45 minutes with a brand new build placed on the device at room temperature. Once the device is left alone for 45 minutes or so the same temperature becomes completely anemic. For instance a temperature of 385 produces no vapor on a soaking wet coil. This is not an exaggeration (picture the steam from you breath on a slightly cold day). If I crank it to 545 F it vapes perfectly. I am experiencing this on 5 different atomizers, and 4 different materials (niFe48, 430, 316 and ni200 -- all single wire spaced coils). Incidentally, I tried the stock materials and also downloaded TFR Curves from Steam Engine. This is my first DNA device so I have nothing to compare it to but I have noticed some things which I think would have an impact on performance but I'm not sure how to address them. 1. The cold ohm reading on the device and in atomizer analyzer is always .02 - .07 ohms lower than my coilmaster ohm reader. This is never not true. 2. After refinement takes place the ohms go down even lower. Usually around .02 lower but sometimes on prolonged periods of not being used as low as .04. 3. I don't know what a "good" Atomizer Analyzer reading looks like but when I screw in an atty and watch I can effect the reading by as much as .15 ohms from initial reading till screwed all the way down. The lowest reading is when it is screwed all the way down. From there I can't reall effect it. It just slightly fluctuates from .001 - .005 which I think is a side effect of the measurement itself. 4. The room temperature is 7 or 8 degrees Fahrenheit higher than the actual temperature. However there are sometimes that it is correct if I check it again later but this is rarely the case. Some things of note: - I did not run Case Analyzer. Instead I uploaded the stock lavabox m settings file found in the downloads section of this site. - Atomizers tried were the Uwell Crown 3, Serpent SMM, Serpent Mini (2 different ones), Kanger Top Tank, an Aspire tank that I can't remember the name of and a Vandy Vape Icon RDA. - To not complicate matters I do not use a preheat and I do not adjust material curves or TCR values. - Of course I could be wrong about all of this and the answer may be that temperature control vaping is only possible with temperatures over 520 Fahrenheit. That was long. Sorry.
  7. This is my first time getting a DNA mod. I use TC SS 316 vaping on a Charon TC right now, around 45-50W at 360-420F. Using Triple core parallel fused clapton 28gx3/36g from AdvancedVapeSupply, see link for my wire I'm using: https://www.advancedvapesupply.com/collections/spooled-ss-prebuilt-wire/products/new-up-to-30-of-triple-core-parallel-fused-clapton-28gx3-core-36g-wrap-316l-ss I am wondering profiles/updates/etc, what should my settings be? I usually build .12 builds, I now see I need .15 or higher for the DNA 75. I can do dual coil 7 wraps to achieve this, but I am new to escribe never used any of this, profiles, etc, is there ones people prefer to use for certain wire etc?
  • Create New...