Jump to content
Evolv DNA Forum

Canadianvape

Members
 View Profile  See their activity

  • Posts

    60

  • Joined

  • Last visited

 Content Type 

Posts posted by Canadianvape

  1. {feature request} up and down to change temp instead of watts

    in EScribe, Software and Firmware

    Posted

    use the gothic theme as a base and you wont have any of this questions after messing with the theme to your liking for like a month, worth it tho, now escribe I only need for updates everything else is in that chip... still frustrated evolv didn't make the 250C read to 0.00001X but I guess that leaves it for the next chip, that increase in accurate resistance reading should enable tc-ka.

  4. Replay Warmth Option

    in General Discussion

    Posted

    It pretty much controls the “warmth” of the vape. Ie in the 250C if you go from TC to replay, the warmth level will change the peak temperature it replays, from watts it applies slightly more voltage than the saved puff. If you want a warmer than you saved puff, you increase it otherwise pull it lower. I guess with the DNA go, you would need device monitor to see the changes in the vape when changing the warmth. I usually use it to get to higher temps by saving then replaying stop puff and saving again the power/temp increases as it is now replaying a boosted hit. 

     

  7. Replay maximum temperature?

    in General Discussion

    Posted

    There is no temp ceiling for replay, that is why high wattage vapers like it. You could be vaping at 800F and it would play it over and over. Technically there is no limit and it WILL replay a burnt hit so it’s down to the user to find the spot and save it. It’s quite annoying sometimes. Switching it from tc into replay is the most inaccurate “replay” tho, you can tell by the monitor how each puff is slightly different when you are recording the temperature and the curve slightly different each time. Too little to notice without the monitor tho.

  8. Early Firmware and EScribe Suite Discussion Thread

    in EScribe, Software and Firmware

    Posted · Edited by Canadianvape
    Forgot to answer part of the question

    On 9/13/2018 at 9:19 AM, James said:

    @Canadianvape, is that new to SP35 on DNA 250C?

    If not, what kind of Ohms change do you see in Device Monitor as the mesh heats? If it's not at least around 20% it may not be Stainless. Do you have it as "Restrict to viable coils." or are you using another mode?

    It’s an rta, mesh is definitely stainless steel, it’s at 0.13ohms  Vandy Vape 150 and 200 micron rolls ss316l . Won’t work with either. Have to get the puff from cold then save and do it again because if I fire it from cold on replay it burns, it’s a prototype so it’s not in the market yet. 

    Edit:it’s on the latest firmware.

  9. Early Firmware and EScribe Suite Discussion Thread

    in EScribe, Software and Firmware

    Posted

    I encountered an error I woke up and went to vape (finder dna250c) and when I clicked fire it said error then a number (sorry I don't remember and I didn't take a picture) after clicking again the message disappeared, it has yet to show up again so I can take a picture, I don't know what triggered it or what it was. sp17. sorry I can't be of more help, but I did catch that white sceen with error, that had not showed up prior to the sp17. also I had to delete two screens from my themes to CHANGE a wire slot, I don't know how that happened. 

  10. Gothic DNA2C/DNA75C by copyman

    in Themes and Custom Screens

    Posted

    I had a different problem, I got some 317l wire in and went to remove the ss430 profile to add the 317l profile, said out of space, on both finder and paranormal. I had gone an installed another theme but that theme had no way of enabling and disabling replay on the theme so I created a screen for it and an icon to lead to that screen, no matter what the icon would not become highlighted and others with the same conditions did. So I came here to get the "light" version, the lock screen sequence programming does not even work in the them so I deleted that and I had created a link to the about screen since that was lacking too, deleted that aswell. now the theme is working.

  11. Early Firmware and EScribe Suite Discussion Thread

    in EScribe, Software and Firmware

    Posted

    Installed in windows 10 intl version. It prompted that there was a new service pack for the dna250c finder and paranormal. Haven’t noticed a difference though. Replay is having a hard time with ss mesh. It will save the puff, let it rest for 5 minutes and it gives a sorching hot hit, only way to make it work is to find the perfect puff every time you pick it up. Quite hot on tc as well. Ss316l 150/200 mesh 

  16. Help with ohms

    in General Discussion

    Posted

    What do you have your ohm lock range set to? The lower it is the more often it will ask the question, Also I don't know to what extent it's in the theme as I haven't experienced that on my dna250c but it's dependant on the time out... maybe setting device to stay on for 20minutes will help? 

  17. Thank You Evolv!

    in General Discussion

    Posted

    I Agree this is amazing, I'm a TC vaper this is the coolest thing I found, You can ALSO start from TC, you know when you go out and it's 10-20c lower and get that super flavour tc vapor? Then just switch to replay and experience THAT SPECIFIC tc puff you liked, that's really something new and for people that have been using tc since the dna40, is extremely nice feature (although theme designer is daunting) 

    thank you evolv :) I love this chipset! 

    The wait was worth it.

    • Like 2

  18. Early Firmware and EScribe Suite Discussion Thread

    in EScribe, Software and Firmware

    Posted

    12 hours ago, maximumsport said:

    What happen to EScribe Suite 2.0 SP15.2 ? Can't find the download link. Can Someone provide it please.

    As far as I'm aware 15.1 is the latest and recommended firmware 33.2 (for the color DNAs) it's pinned in early EScribe thread, the one with the files,  this is the discussion. 

    Im hoping for Evolv to make Theme Designer more user friendly as I want to make a theme myself. (Firmware seems very solid) 

    33.2 has replay for the 75C and sp15.1 changes some settings in the default evolv theme.

    hope this helps

  21. setting temperature

    in General Discussion

    Posted

    Any links to tutorial videos where they show where to change the wattage amount and the temperature would be really useful, spent the whole day combing the internet and watching videos yet none tell me where to change those values, the place they were in 1.5 is gone and I'm not familiar with this new EScribe .

  23. Boost versus Punch

    in General Discussion

    Posted

    Boost is set is EScribe or depending on your theme, on the device, it's for tc and in the 250c can be set 200/300/400w doesn't nesesarly use that, just makes ramp up to temp non existent. Boost is for power mode, I think it's more like % of what you have set another member can help you, I only use tc and replay.

×
×
  • Create New...