dwcraig1

Moderators
  • Content Count

    1,802
  • Joined

  • Last visited

  • Days Won

    59

Everything posted by dwcraig1

  1. dwcraig1

    Evolv colour screens

    It's my Drone 250C that has the "lesser" screen.
  2. dwcraig1

    Only works on charger

    What does it show when connected to EScribe? Open a ticket with Evolv here: https://helpdesk.evolvapor.com/index.php?a=add&category=1
  3. dwcraig1

    Evolv colour screens

    I have different themes on the three that I have, one appears similar to the one of yours on the left. I just changed the theme on the suspect one and it looks like yours on the left when viewed at an angle.
  4. dwcraig1

    watts calcuator

    I must admit that I never have tried it. It is under the "TOOLS" tab at the top left of the main EScribe window, mine says "not installed" when I select it. I am using the International version BTW
  5. dwcraig1

    watts calcuator

    I'm pretty sure when you start the install process there are some boxes that need to be checked for additional features, the calculator is one I believe. Just reinstall your version of EScribe, no need to uninstall first. Be sure to get the full install and not just the service pack.
  6. dwcraig1

    Display gone BAD

    Might check Ebay, just an idea. Or, https://www.amazon.com/gp/offer-listing/B07NKLFF6Y/ref=dp_olp_new_mbc?ie=UTF8&condition=new Malaysia is listed but I don't know how much for shipping.
  7. dwcraig1

    Lost Vape Paranormal dangerous overheat

    I would suspect you to get the results your wanting by submitting a ticket with Evolv. Here is a video of the 166 Paranormal, you can figure that it's going to be wired the same. The battery door is where the cells are bridged in a series. I short inside the battery door for the contact marked with a plus would only effect the one cell (the inside one). If the 2nd cell still has a good charge after getting hot I would look there. Up on top where the red wire comes off from the top of the inboard cell that should effect both cells the same. That red wire runs the whole way from the top to the B+ on the board so there is plenty chance for a problem. While you may not want to try to do it yourself you may find it informative.
  8. dwcraig1

    Lost Vape Paranormal dangerous overheat

    So it it the battery closest to the board or the last one in?
  9. dwcraig1

    Lost Vape Paranormal dangerous overheat

    The way I figured it since the cells are in a series a short on the board would heat both cells pretty much evenly. But of coarse I can only guess at it.
  10. dwcraig1

    Lost Vape Paranormal dangerous overheat

    I would think that the problem is before the board, battery sled, wiring, Ect. They do Lost Vape's warranty work as well as warrant the board, get help with it here if needed: https://helpdesk.evolvapor.com/index.php?a=add&category=1
  11. dwcraig1

    Devices For Sale?

    Here for on board fire switch: https://www.ebay.com/itm/222560648352?var=&ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649
  12. dwcraig1

    Can't read Sh^t

    Yep, I really like it too.
  13. Assuming they worked OK before sitting I'd start by cleaning/polishing the end of the mod's 510 positive pin. If that doesn't do it I'd check the solder joints board to 510 looking for corrosion. Does Atomizer Analyzer show any connection?
  14. dwcraig1

    Need help with a dead 250

    Open a ticket with Evolv here: https://helpdesk.evolvapor.com/index.php?a=add&category=1 If it was mine I'd check the solder joints on the balance tap on the board looking for cold solder joints.
  15. dwcraig1

    Curve Mode On DNA Devices?

    No, not there.
  16. dwcraig1

    Curve Mode On DNA Devices?

    If using the INT firmware version there is a boost feature when material is set to Watts. You may get that to work to your liking.
  17. dwcraig1

    4 Red flashes

    No idea
  18. dwcraig1

    4 Red flashes

    Full charge on a LiPo is 4.2 so if that's correct there is a major problem. Go here for help with it: https://helpdesk.evolvapor.com/index.php?a=add&category=1
  19. dwcraig1

    4 Red flashes

    Does it show battery voltage?
  20. dwcraig1

    4 Red flashes

    That sounds like what it will do when then battery is too low to operate it. Perhaps the battery is at fault, check the voltage drop using EScribe's Device Monitor.
  21. dwcraig1

    Vapecige VTX 250C Battery Charge Problem

    Yes I removed the board and put it in an SXK Boxer squonk. I then checked out the problem with the VTX's 510, the o-ring they used was too small.
  22. dwcraig1

    Vapecige VTX 250C Battery Charge Problem

    Mine leaked badly from the 510 after about a week as many other users had reported.
  23. dwcraig1

    Over night charge

    The charger on the Go board will stop charging when the battery is full charged. As with any battery either in or out of the mod should never be charged unattended unless in a safe fire proof place.
  24. dwcraig1

    Need help with a dead 250

    Try removing device, close EScribe, connect device to computer and open EScribe again. A PM has been sent.
  25. dwcraig1

    Need help with a dead 250

    That screen is "Device Monitor". It can be run separate from the main EScribe , try and locate your main EScribe. Do you have a volt meter and a stand alone 18650 battery charger?