dwcraig1

Moderators
  • Content Count

    1,796
  • Joined

  • Last visited

  • Days Won

    57

Everything posted by dwcraig1

  1. dwcraig1

    VTBOX 200 USB Charge show 3.08A

    Did this happen as soon as you tried it after cleaning the switch, or did it take awhile to develop?
  2. dwcraig1

    VTBOX 200 USB Charge show 3.08A

    Being that the battery appears to have been sitting well below 2.8 volts (providing that volt reading is accurate) the battery surely has internal damage. With that being said I would think that the board is what's causing the problem. But I don't know for sure.
  3. dwcraig1

    VTBOX 200 USB Charge show 3.08A

    Does the mod function or throw a battery error?
  4. dwcraig1

    VTBOX 200 USB Charge show 3.08A

    First off I can't imagine a computer USB putting out that much power. Do you have a volt meter where you can measure the actual voltage of the battery?
  5. dwcraig1

    Warranty Return

    Probably best to start the process here: https://helpdesk.evolvapor.com/index.php?a=add&category=1
  6. dwcraig1

    Orion DNA pod mod low fire issue

    The maximum voltage output on a Go board is around 3.5 volts, figure from there what resistance is needed to attain up to 30 watts. An Orion DNA pod can barely handle 20 watts with the 0.25 one, less with the .5
  7. dwcraig1

    Think Vape Finder DNA250C issues

    Poor connections between the cells and board need to be ruled out. You should be able to get your full power setting in non TC until your cells sag to below the Cell Soft Cutoff. The misfiring , does that happen when using EScribe to fire it? Would you post a snippet like this one?
  8. dwcraig1

    Constant temp protect warning in wattage mode

    I've been vaping for about 7 years now and I'm not sure if I've ever seen an aluminum 510 . In the old days a lot of them were nickle plated brass and they wore quite quickly. Most all of today's 510's are stainless steel. The colored one generally have coating similar to what's used on fire arms. This coating if on the on threads interferes with conduction. The DNA250 board model wise is about as good of a board has one can get, that being said my guess is some type of connection issue between the board and the coil. The lower the ohms of the load the more critical accurate connections become.
  9. dwcraig1

    New DNA Go Device

    It appears to me that the Jazz had a name change
  10. dwcraig1

    Reply hit or miss. Any advise?

    I deleted my post about the warm atty a few minutes after posting as I was unsure if it was the cause.
  11. dwcraig1

    250 colours stop working with white dispay

    Has another USB cable been tried?
  12. There have been many known cases where the fire button pinches the ribbon cable of the screen .
  13. dwcraig1

    Aludirome UN2 materials csv???

    Use Device Monitor in Escribe to determine if it has a resistance change from cold to hot, it is my understanding that this material is similar to Kanthal which is not a TC material. EScribe will help you determine that.
  14. dwcraig1

    Nifethal 52 and 250c

    It's not a curve but should work just as well as the curve is almost linear anyway. It may make a slight difference, might not, use the one that seems to work best.
  15. dwcraig1

    Is USB charging BRICKING ALL my DNAs?!

    When ever there is a cell with an impossible voltage reading like the one that is 5.22 volt the battery management IC has gone bad.
  16. While I have no real idea I have seen this before caused by a wonky USB cable/port.
  17. dwcraig1

    Nifethal 52 and 250c

    This is the one pertaining to your settings. 0.065 ohms should be no problem
  18. dwcraig1

    Nifethal 52 and 250c

    This is 250C 2S output power
  19. dwcraig1

    Nifethal 52 and 250c

    The 2nd fire is using SteamEngine's Alloy 52, other 3 are for NiFe 48 Zivipf NiFe is 400 (or 0.004) Alloy 52 is 403.6 (or 0.00436)
  20. dwcraig1

    Nifethal 52 and 250c

    I was hoping Wayne would show up this morning. I put a coil of Zivipf NiFe48 in a RBA, it's 2 strands of tightly twisted 26 gauge. Included here is the correct CSV for temp coefficient of NiFe48. 48 and 52 are close but not the same. The snip is of using setting for both 48 and 52, 48 is on the far left and far right, forget the center ones. What I was wanting to see was the increase in resistance when heated, note it darn near doubles. Preheat is set to 75 watts. NiFe48.csv
  21. dwcraig1

    Is USB charging BRICKING ALL my DNAs?!

    Does Device Monitor in EScribe show any of the cells above 4.2 volts?
  22. dwcraig1

    Is USB charging BRICKING ALL my DNAs?!

    Evolv will warranty the new board from Protovapor with your installation. On your VT250S, ask them here: https://helpdesk.evolvapor.com/index.php?a=add&category=1 Was the same powered hub used to charge these, possibly a problem, worth a mention.
  23. dwcraig1

    Nifethal 52 and 250c

    Use Windows Snipping tool available in Win 7 and above.
  24. dwcraig1

    Replay mode

    Replay will work with Kanthal or Nichrome coils only when there are numerous poor connections between the board and coil resulting in a resistance change due to voltage loss between the parts. Only TC wire is supported with Replay, Nichrome and Kanthal are not.
  25. dwcraig1

    Translations

    It might be best to contact James here, might not see it otherwise. https://helpdesk.evolvapor.com/index.php?a=add&category=5