Jump to content

retird

Moderators
  • Posts

    2,610
  • Joined

  • Last visited

  • Days Won

    134

Posts posted by retird

  1. My point was that there can be many causes... that's all...Vapor Shark should know what common issues they have with their device.  A good place to start I think...  and no I did not read your post before I posted as I was typing as you posted.  You are right in asking for more details.  I'm sure that Dilligaf will get it sorted...

  2. Each of us could "guess" what your issue is.  We can't evaluate your device however, so the cause is a mystery to all of us.  It is like me calling my Honda dealer and saying my car quit running and you must tell me over the phone what the problem is.  I'm not Evolv but many things can be the cause.  See what Vapor Shark says and does as they are pretty good at standing behind their stuff I'm told. The Evolv board has a warranty if that is determined to be the issue.

    Not knowing anything about your device I will offer a few guesses:

    Bad Battery
    Poor connections
    Bad daughter board
    Device dropped and internals were damaged
    Bad fire button
    Display broken thus won't light up
    Poorly connected display ribbon
    Bad usb cable thus not recognized by EScribe
    ETC
    ETC

  3. BillW50 said:



    Really? I am into RC and my lipos are horrible for battery sag. Same ones that the DNA200 often uses. And the electric car manufacturers have lots of smart scientists, researchers, and engineers. And oddly enough they are using 18650s for their battery packs. So you better call them and set them straight. :)



    They also use Li-Po's for their battery packs...  just one example...  http://www.ronlund.com/rcheli-prod/ELEC_BATL6/CS5200-6S-50C.html

  4. jurdanas said:



    Hello.
    And it's my problem.
    Fire button work good. "Fire button" is "Fire button", but the automatic locking when pressed - the program "2016-02-29 EScribe 1.0.42" is working wrong. We are using a "trial" version.
    I think the "program" is working bad. (I have 2S mode 18650)
    Sorry.
    Thanks.

    If you think it is the 2016-02-29 firmware you can install a previous firmware versiuon and see if that fixes it
  5. Scy123 said:

    When I change it from do not show to show temp it flashes the coil temp when it goes over temperature.

    Here is a pic. It normally shows watts but when I go over temperature it flashes the temp. Also where the temp use to be it changes to watts.
    [M0tD16b] 

    Language and local settings on both my PC and VirtualBox are both set to English United States and United Stats. I never changed any of those settings. unless a program I installed changed it, it should be default.



    THANKS.... I was expecting a flashing message when the fire button is released too... the "Show Temperature" changes the wattage displayed to Temperature and goes away when the fire button is released,,... thanks again....
  6. VapingBad said:

    It is doing what it's meant to constantly the temp on screen, of course if you are vaping at the temp limit there is not much to see.



    So there is no shown "message" for that setting?

    There are three choices for that theme. Don't Show, Show Temperature, and Show Message.   When Show message is selected it flashes Temperature Protected when Temp is reached, when Don't Show is selected it doesn't flash a message even tho temp is reached.  When selecting Show Temperature it flashes no message either even tho temp is reached. So what is the purpose and function of the Show Temperature setting?  I'm just trying to figure out if some message is supposed to flash and show something.  If not then that setting does the same thing as the Don't Show setting.  If it is supposed to flash a message I don't see one thus it may need to be identified as a bug than can easily be fixed.   
  7. OK, I was just fiddling around with themes and ran across this.  Go to Themes.

    Go to theme, Custom Screens, Temperature Protected

    Set it to “Show Temperature”

    Upload it and when temp is reached while firing it doesn’t  show any message for” temperature” as it does when setting it to  “Show Message” it shows “Temperature Protection” message.

    What step am I missing here.  Tried on several DNA200's.  



×
×
  • Create New...