Settings
39 files
-
Lost Vape Therion DNA 75C
This is a fully configured Escribe settings file for the new Lost Vape Therion DNA 75C. The mod basically came unconfigured at the stock board settings which was surprising. This config file has been meticulously configured, and includes the following highlights:
All 8 profiles configured, with: 3 temp control profiles for favorite atomizer and build combos. My go-to is the Pharaoh RTA as the primary profile, plus the Crown III and the SMOK Baby Beast for emergencies while traveling 5 power-only profiles, at presets of 35, 40, 45, 50 watts Includes my posted DNA 75C Enhanced Default Theme v2.2 which greatly expands the stock theme's capabilities Standard materials plus two SS316L materials, one curve and one TCR set at 0.00094 Mod fully configured: Battery Analyzer run for dual HohmTech Life 3000mah 18.04wh 18650's Cell Soft Cutoff set to lower limit of these 18650's at 2.9v to protect the batteries Input currents set for battery safety based on Mooch's test results Output currents set at DNA 75C spec sheet typical rating Mod internal resistance measured with copper plug at 0.004 ohms Case Analyzer run at 73 degF ambient, averaged over 3 runs Hope everyone enjoys!
3,381 downloads
-
Lost Vape Mirage DNA 75C
This is a fully configured Escribe settings file for the new Lost Vape Mirage DNA 75C. Highlights:
All 8 profiles configured, with: 3 temp control profiles for favorite atomizer and build combos. My go-to is the Pharaoh RTA as the primary profile, plus the Crown III and the SMOK Baby Beast for emergencies while traveling 5 power-only profiles, at presets of 35, 40, 45, 50 watts Includes my posted DNA 75C Enhanced Default Theme v2.2 which greatly expands the stock theme's capabilities Standard materials plus two SS316L materials, one curve and one TCR set at 0.00094 Mod fully configured: Battery Analyzer run for iJoy 21700 3750 mAh 40A battery Cell Soft Cutoff set to 2.75V, max sustained discharge at 24A, max peak discharge at 35A for longer cell life Output currents set at DNA 75C spec sheet typical rating Mod internal resistance at 0.0031 ohms, measured with copper plug (actual 0.004 x 80%, minus an extra 0.1 mOhm for kick(s) Built for EScribe Suite International v2.0 SP12 or higher, running beta firmware v1.1 SP27 or higher Hope everyone enjoys!
1,497 downloads
-
Lost Vape Paranormal DNA166 (Evolv DNA 250)
By iAlexander
This is the stock .ecig file for theLost Vape Paranormal DNA 166 (Evolv DNA 250), 2 x 18650 batteries mod, providing manufacturer/original configuration as it was out of the box.
Also have attached separately the original Lost Vape Theme file.
1,458 downloads
- lost vape
- paranormal
- (and 3 more)
-
flawless vape Evolv DNA 250 Set
By Tugnick
General escribe goodies.
Case's Thermal balanced
Check out, lipo Discharge Graph on soft Cutoff too!
Long life, Puff oriented. Have fun
1,886 downloads
-
Evolv DNA 75 Color Default Settings
By James
These are the default settings for the Evolv DNA 75 Color.
1,607 downloads
0 comments
Submitted
-
paranormal NEW ORIGINAL SETTINGS 2019 LOST VAPE PARANORMAL DNA250C
LOST VAPE DEFAULT SETTINGS PARANORMAL DNA250C 2019
1,969 downloads
0 comments
Updated
-
Hcigar VTinbox BF DNA 75 V_23112017
By Kronos
HCIGAR VT Inbox DNA 75 by Kronos Version V_23112017
V1.0 : Settings on Stainless Steel 316 Dual Coils setup w/ Bottom Feed Atom
features: Temperature control & Wattage control
Profiles:
1- ROCK / ROCK- SS316 TC=240C Power=40W Punch=5 PreHeath=50W (temperature dominant)
2- ROLL / ROLL- SS316 TC=240C Power=45W Punch=6 PreHeath=55W (temperature dominant)
3- HELL / HELL- SS316 TC=260C Power=55W Punch=7 PreHeath=65W (temperature dominant)
4- PUMP / PUMP- SS316 TC=280C Power=65W Punch=8 PreHeath=75W (temperature dominant)
5- ACID / ACID- SS316 TC=275C Power=50W Punch=9 PreHeath=75W (temperature dominant)
6- POWER CONTROL / PWCT- SS316 TC= no Power=70W Punch=0 PreHeath=no
7- RELAXED / CALM- SS316 TC=250C Power=50W Punch=5 PreHeath=60W
8- NO PREHEAT / NOPH- SS316 TC=250C Power=75W Punch=1 PreHeath=1W
main design: apple style logo/font (three rows)
preferred with: Flavour chasing / Cloud chasing
author: KRONOS (link: https://www.facebook.com/KR0NOS )
club: GIAMBELLINO VAPERZ (link: https://www.facebook.com/groups/Giambevaperz/ )
city: MILANO
state: ITALY
nation: EUROPEAN UNION
766 downloads
0 comments
Updated
-
Lost Vape Triade DNA250c profile after resistance and case analyzer tests
By slash1981
Lost Vape Triade DNA250c settings (.ecig) after case analyzer and resistance tests on triple VTC6.
Battery Analyzer run for triple Sony VTC6 3000mah 17.899wh Cell Soft Cutoff set to lower limit of these 18650's at 2.75v Mod internal resistance measured with copper plug at 0.006 ohms Case Analyzer run at 73F ambient.567 downloads
-
lost vape Lost Vape Drone DNA 167 BF mod Settings
By ed101
Settings file for the Lost Vape Drone DNA 167 BF mod. Battery analyser run for a pair of Sony VTC5A's. Material profiles from SteamEngine.
441 downloads
0 comments
Submitted
-
Lost Vape Centaurus DNA250C default settings
By Akos
Default escribe settings of Lost Vape Centaurus DNA250C mod.
1,258 downloads
0 comments
Submitted
-
Think Vape Finder DNA 250C default .ecig file
By maximumsport
Default file values for the Think Vape Finder 250C
692 downloads
-
Lost vape Paranormal DNA75C
By Frank65
Original Lost Vape Paranormal DNA75C stock settings (.ecig file)
750 downloads
- paranormal
- ecig
- (and 1 more)
0 comments
Updated
-
Lavabox 75 - Tweaked SS316 Settings
By Fadelio
I tweaked the settings on my lavabox M DNA 75 chip after running the case analyzer. Please post your changes/ comments.
Variables:
Lavabox 75 M - DNA 75 Chip
Geekvape Ammit single coil
Stainless Steel 26 gauge (from Master of Clouds)
Sony VTC5 Battery
439 downloads
-
Volcano Lavabox M (Mini) DNA 75 Stock Settings (Out of the box)
This is the stock .ecig file for the Volcano Lavabox M (Mini) DNA 75 1650 mod, providing manufacturer/original configuration as per out of the box.
613 downloads
- volcano
- manufacturer settings
- (and 2 more)
0 comments
Submitted
-
Lost Vape Paranormal DNA75C after test
By Frank65
Lost Vape Paranormal DNA75C settings (.ecig) after case analyzer , resistence test and VTC6 battery test.
Battery Analyzer run for dual Sony VTC6 3000mah 17.899wh Cell Soft Cutoff set to lower limit of these 18650's at 2.75v Mod internal resistance measured with copper plug at 0.015 ohms Case Analyzer run at 70 degF \ 21 °C ambient, average over 3 runs Materials and profiles as per my personal use428 downloads
- lost vape
- paranormal
- (and 1 more)
0 comments
Updated
-
0 comments
Submitted
-
Thelema DNA250c Stock config/settings
Just unpacked my new DNA device which arrived today!
This is out-of-the-box settings from the device.
Have fun ;-))
Production History Monday, November 2, 2020, 3:12 PM @ Shenzhen, Guangdong, China Mod configured Tuesday, October 13, 2020, 12:11 PM Board programmed855 downloads
0 comments
Submitted
-
Lost Vape - Drone 250c (2019 / UK) Stock Settings
By fapfare
Lost Vape Drone (upgraded 2019 version, DNA250c) stock settings. Nothing changed, factory fresh.
324 downloads
0 comments
Submitted
-
Vapor Shark DNA 250 Settings
By dclanz
Here is the default config for the Vapor Shark DNA 250
426 downloads
0 comments
Submitted
-
Jac Vapour Series B DNA75 Default/stock settings
By Wayneo
Full setup by Jac Vapour for their DNA75 SeriesB, including;
Battery curve for Samsung 25R
Thermal calibration
Internal mod resistance set.
482 downloads
0 comments
Submitted
-
odin Odin DNA 250c - Watt Friendly
By producer_ben
I'm fairly new to DNA Chips and at present I am not a big user of temp control.
The factory presets on the ODIN DNA 250c I found to be heavily based around TEMP control and had a lot of presets on that weren't suitable for myself as a wattage based user. So I modified the presets to current personal tastes and thought I'd add it incase anyone else was "in the same boat".
Below are a list of the presets with an outline of what they do :
Kanthal : Standard "Watt" mode with no punch or boost
Watt Punch : Standard "Watt" mode with a boost of +2 and Punch enabled
Watt Boost : As above, but with Punch disabled
Watt Replay : Standard "Watt" mode, but with Replay enabled
Watt Boost Replay : Standard "Watt" mode, but with a boost of +2 and Replay enabled
SS 316 : Standard Odin Default
SS 430 : Standard Odin Defeault
Replay : Standard Odin Default
*Starting "Watt" amount is preset to 20 on all modes except Kanthal which is preset to 30. This is to avoid any accidental coil damage.
*No coil ohms or temperatures have been pre-set for the same reasons as above.
I hope this helps somebody out at some point. I will be uploading a "matching" theme as I have tweaked mine ever so slightly and found it makes a huge difference, without going overboard.
Vape safe everybody
227 downloads
- vaping bogan
- dovpo
- (and 3 more)
0 comments
Submitted
-
Paranormal 75c stock settings
By Dimrx
This is the stock .ecig file for the Lost Vape Paranormal 75C
414 downloads
0 comments
Submitted
-
VapeCige VTbox 250 Settings
By dclanz
Here is the default config file for the VapeCige VTBox 250. Please note that none of the profiles are configured properly by default (most are set to nickel and titanium, that's how I got it) so if you use it, be sure to go through and set the presets to your liking.
401 downloads
0 comments
Submitted
-
odin Dovpo Odin 250c Default Settings
By M666
Default escribe settings of Dovpo Odin mod.
509 downloads
0 comments
Updated
-
0 comments
Submitted