22 files

  1. Lost Vape Paranormal DNA166 (Evolv DNA 250)

    This is the stock .ecig file for theLost Vape Paranormal DNA 166 (Evolv DNA 250), 2 x 18650 batteries mod, providing manufacturer/original configuration as it was out of the box.
    Also have attached separately the original Lost Vape Theme file.

    1,365 downloads

       (1 review)

    1 comment

    Updated

  2. Lost Vape Therion DNA 75C

    This is a fully configured Escribe settings file for the new Lost Vape Therion DNA 75C. The mod basically came unconfigured at the stock board settings which was surprising. This config file has been meticulously configured, and includes the following highlights:
    All 8 profiles configured, with: 3 temp control profiles for favorite atomizer and build combos. My go-to is the Pharaoh RTA as the primary profile, plus the Crown III and the SMOK Baby Beast for emergencies while traveling 5 power-only profiles, at presets of 35, 40, 45, 50 watts Includes my posted DNA 75C Enhanced Default Theme v2.2 which greatly expands the stock theme's capabilities Standard materials plus two SS316L materials, one curve and one TCR set at 0.00094 Mod fully configured: Battery Analyzer run for dual HohmTech Life 3000mah 18.04wh 18650's Cell Soft Cutoff set to lower limit of these 18650's at 2.9v to protect the batteries Input currents set for battery safety based on Mooch's test results Output currents set at DNA 75C spec sheet typical rating Mod internal resistance measured with copper plug at 0.004 ohms Case Analyzer run at 73 degF ambient, averaged over 3 runs Hope everyone enjoys!
     

    3,140 downloads

       (1 review)

    15 comments

    Updated

  3. Lost Vape Mirage DNA 75C

    This is a fully configured Escribe settings file for the new Lost Vape Mirage DNA 75C. Highlights:
    All 8 profiles configured, with: 3 temp control profiles for favorite atomizer and build combos. My go-to is the Pharaoh RTA as the primary profile, plus the Crown III and the SMOK Baby Beast for emergencies while traveling 5 power-only profiles, at presets of 35, 40, 45, 50 watts Includes my posted DNA 75C Enhanced Default Theme v2.2 which greatly expands the stock theme's capabilities Standard materials plus two SS316L materials, one curve and one TCR set at 0.00094 Mod fully configured: Battery Analyzer run for iJoy 21700 3750 mAh 40A battery Cell Soft Cutoff set to 2.75V, max sustained discharge at 24A, max peak discharge at 35A for longer cell life Output currents set at DNA 75C spec sheet typical rating Mod internal resistance at 0.0031 ohms, measured with copper plug (actual 0.004 x 80%, minus an extra 0.1 mOhm for kick(s) Built for EScribe Suite International v2.0 SP12 or higher, running beta firmware  v1.1 SP27 or higher Hope everyone enjoys!

    826 downloads

       (2 reviews)

    4 comments

    Updated

  4. Lost Vape Drone DNA 167 BF mod Settings

    Settings file for the Lost Vape Drone DNA 167 BF mod. Battery analyser run for a pair of Sony VTC5A's. Material profiles from SteamEngine.

    276 downloads

       (0 reviews)

    0 comments

    Submitted

  5. Evolv DNA 75 Color Default Settings

    These are the default settings for the Evolv DNA 75 Color.

    1,158 downloads

       (0 reviews)

    0 comments

    Submitted

  6. Lost vape Paranormal DNA75C

    Original Lost Vape Paranormal DNA75C stock settings (.ecig file)
     

    461 downloads

       (0 reviews)

    0 comments

    Updated

  7. Lost Vape Paranormal DNA75C after test

    Lost Vape Paranormal DNA75C settings (.ecig) after case analyzer , resistence test and VTC6 battery test.
    Battery Analyzer run for dual Sony VTC6 3000mah 17.899wh Cell Soft Cutoff set to lower limit of these 18650's at 2.75v Mod internal resistance measured with copper plug at 0.015 ohms Case Analyzer run at 70 degF \ 21 °C ambient, average over 3 runs Materials and profiles as per my personal use

    314 downloads

       (0 reviews)

    0 comments

    Updated

  8. FCSHARE

    These files are for dry vape devices only.   Make sure to use correct cold ohms for your Device 
    All testing was  done using a 19/22 stem basket style fine mesh screen.
    The RBT Splinters with  the shorter stems and wider mesh may need to increase temperature or switch material for best results. For SplinterZ I suggest the 316L material file.
    If you need to go above the 445 degree  mod safety cutoff in the DNAc you will need to increase maxs output temperature setting. 
     
     
     
     
     Please load from file not as a theme.
    Custom profiles  and tweaks to escribe settings have been made. A assortment of custom SS materials is also  preloaded. 
    Be sure to adjust with your mods  resistance settings.
    If unsure use of the mod resistance use whats  in these settings (0.004) 
    DNA download is based off a Wismec Reuleaux DNA250 .
    Profiles  for iheat, Splinter/ SplinterZ  and Stempod dry atomizers.
     Along with custom settings to puff time etc.
    Included are a custom FC theme in the  DNA  download
    DNA Profiles contain the material cvs and setting. Load as a profile
    iheatDNA.ecigprofile
    SplinterDNA.ecigprofile
    SplinterZDNA.ecigprofile
    StempodDNA.ecigprofile
     
     
    DNAc based off a Lost Vape Paranormal DNA250c use with 2 battery mods
    The maxs output temperature  is set to 445 in this file 
    Maxs puff time 20 seconds 
     
    These files have have profiles with custom setting for iheat, stempod, splinter/ splinterZ.  
    Once  you install these files you can change the themes with out lossing these settings.
    Open these files  with escribe.
    Then use theme designer if you like to try other themes. Below are tested themes for DNAc mods
    Evolv Default Enhanced 250C.ecigtheme
    For use with iheat Splinter/Splinter Z and stempod.
    Should work in both DNA75c/250c. 
     Please use DNAc
     
    DNAc Profiles contain the material cvs and setting. Load as a profile
     
    StempodDNAc.ecigprofile
    SplinterZDNAc.ecigprofile
    iheatDNAc.ecigprofile
    SplinterDNA.ecigprofile
     
    Triade based off of Lost Vape Triade DNAc use with 3 battery mods
    2 test profiles added that are based  on stem size
    Use the above Splinter DNAc profile if test files give you any issues.
     
     
    SplinterZ19:19stem.ecigprofile
    SplinterZ19:22stem.ecigprofile
     
     

    359 downloads

       (0 reviews)

    0 comments

    Updated

  9. Vapor Shark DNA 250 Settings

    Here is the default config for the Vapor Shark DNA 250

    181 downloads

       (0 reviews)

    0 comments

    Submitted

  10. VapeCige VTbox 250 Settings

    Here is the default config file for the VapeCige VTBox 250. Please note that none of the profiles are configured properly by default (most are set to nickel and titanium, that's how I got it) so if you use it, be sure to go through and set the presets to your liking.

    210 downloads

       (0 reviews)

    0 comments

    Submitted

  11. Vapedroid Sbody C2D1 factory .ecig file

    C2D1 factory .ecig file sent to me by Sbody

    170 downloads

       (0 reviews)

    0 comments

    Submitted

  12. Volcano Lavabox DNA 200 900mah defaults

    These settings contain the default presets for the Volcano Lavabox DNA 200 using the 900mah LiPo battery.

    67 downloads

       (0 reviews)

    0 comments

    Submitted

  13. Volcano Lavabox DNA 200 1300mah defaults

    These settings contain the default presets for the Volcano Lavabox DNA 200 using the 1300mah LiPo battery.

    94 downloads

       (0 reviews)

    0 comments

    Submitted

  14. Paranormal 75c stock settings

    This is the stock .ecig file for the Lost Vape Paranormal 75C 

    254 downloads

       (0 reviews)

    0 comments

    Submitted

  15. Volcano Lavabox M (Mini) DNA 75 Stock Settings (Out of the box)

    This is the stock .ecig file for the Volcano Lavabox M (Mini) DNA 75 1650 mod, providing manufacturer/original configuration as per out of the box.

    368 downloads

       (0 reviews)

    0 comments

    Submitted

  16. Lost Vape Triade DNA250c profile after resistance and case analyzer tests

    Lost Vape Triade DNA250c settings (.ecig) after case analyzer and resistance tests on triple VTC6.
    Battery Analyzer run for triple Sony VTC6 3000mah 17.899wh Cell Soft Cutoff set to lower limit of these 18650's at 2.75v Mod internal resistance measured with copper plug at 0.006 ohms Case Analyzer run at 73F ambient.

    174 downloads

       (0 reviews)

    9 comments

    Submitted

  17. Lavabox 75 - Tweaked SS316 Settings

    I tweaked the settings on my lavabox M DNA 75 chip after running the case analyzer.  Please post your changes/ comments. 
    Variables: 
    Lavabox 75 M - DNA 75 Chip
    Geekvape Ammit single coil
    Stainless Steel 26 gauge (from Master of Clouds)
    Sony VTC5 Battery 

    249 downloads

       (0 reviews)

    5 comments

    Submitted

  18. Evolv DNA 250 Set

    General escribe goodies.
    Case's Thermal balanced
    Check out, lipo Discharge Graph on soft Cutoff too!
    Long life, Puff oriented. Have fun

    1,249 downloads

       (0 reviews)

    0 comments

    Submitted

  19. my_default_dna200

    work backup

    390 downloads

       (0 reviews)

    0 comments

    Submitted

  20. Paranormal 250C Default

    Default settings

    117 downloads

       (0 reviews)

    0 comments

    Submitted

  21. Think Vape Finder DNA 250C default .ecig file

    Default file values for the Think Vape Finder 250C 
     

    390 downloads

       (0 reviews)

    1 comment

    Submitted

  22. Hcigar VTinbox BF DNA 75 V_23112017

    HCIGAR VT Inbox DNA 75 by Kronos Version V_23112017
    V1.0 : Settings on Stainless Steel 316 Dual Coils setup w/ Bottom Feed Atom
    features: Temperature control & Wattage control
    Profiles:
    1- ROCK / ROCK- SS316 TC=240C Power=40W Punch=5 PreHeath=50W (temperature dominant)
    2- ROLL / ROLL- SS316 TC=240C Power=45W Punch=6 PreHeath=55W (temperature dominant)
    3- HELL / HELL- SS316 TC=260C Power=55W Punch=7 PreHeath=65W (temperature dominant)
    4- PUMP / PUMP- SS316 TC=280C Power=65W Punch=8 PreHeath=75W (temperature dominant)
    5- ACID / ACID- SS316 TC=275C Power=50W Punch=9 PreHeath=75W (temperature dominant)
    6- POWER CONTROL / PWCT- SS316 TC= no  Power=70W Punch=0 PreHeath=no
    7- RELAXED / CALM- SS316 TC=250C Power=50W Punch=5 PreHeath=60W
    8- NO PREHEAT / NOPH- SS316 TC=250C Power=75W Punch=1 PreHeath=1W
     
    main design: apple style logo/font (three rows)
    preferred with: Flavour chasing / Cloud chasing
    author: KRONOS (link: https://www.facebook.com/KR0NOS )
    club: GIAMBELLINO VAPERZ (link: https://www.facebook.com/groups/Giambevaperz/ )
    city: MILANO
    state: ITALY
    nation: EUROPEAN UNION

    1,199 downloads

       (0 reviews)

    0 comments

    Updated